[Equest-users] Window "Curb"

[John Aulbach]

Hi Alex:

Dumb Question.

Doesn't the eQuest Windows library allow you to chose glazing with a certain 
type of fram (wodd, aluminum, thermal bridge, no thermal bridge)?

John R. Aulbach, PE, CEM
Senior Energy Engineer

________________________________

PartnerEnergy
1990 E. Grand Avenue, El Segundo, CA 90245
W: 888-826-1216, X254| D: 310-765-7295 | F: 310-817-2745
www.ptrenergy.com| jaulbach at ptrenergy.com
 
 




________________________________
From: Alex Krickx <akrickx at seriousmaterials.com>
To: Jeremy Goth <jngoth at hotmail.com>
Cc: "equest-users at lists.onebuilding.org" <equest-users at lists.onebuilding.org>
Sent: Wed, January 5, 2011 8:43:44 AM
Subject: Re: [Equest-users] Window "Curb"


Thanks Bruce and Jeremy,
 
Well, you’ve answered my question but I still have the same problem: how to 
account for edge-of-glass effects in eQUEST (the edge of glass U-value will be 
between the frame and COG values). Back to the drawing board I guess. Thanks for 
the responses.
 
Kind regards,
Alex Krickx
 
From:Jeremy Goth [mailto:jngoth at hotmail.com] 
Sent: Wednesday, January 05, 2011 8:26 AM
To: Alex Krickx
Cc: equest-users at lists.onebuilding.org
Subject: RE: [Equest-users] Window "Curb"
 
Go to your building shell and navigate to the space/roof/skylight in the 
component tree.  Select the skylight then go to the spreadsheet tab on the right 
and find 'Skylight Surface - Curb - Performance'.
 
Jeremy
 

________________________________

Date: Tue, 4 Jan 2011 20:00:19 -0500
From: bruce5 at bellnet.ca
To: akrickx at seriousmaterials.com
CC: equest-users at lists.onebuilding.org
Subject: Re: [Equest-users] Window "Curb"

    A curb is used to lift the window up off the roof and allow the window to be 
flashed and made water tight.  It can be as simple as a 2x6 or 2x8 wood box.  A 
complicated one would be a fully insulated wall tunnel through a roof truss 
system.  It should be modelled as an exterior wall.  There should be no edge of 
glass effect as all the glass should be inside the opening.  There will be an 
edge/corner effect where the window frame sits on the curb.
Bruce Easterbrook P.Eng.
Abode Engineering


On 04/01/2011 04:12 PM, Alex Krickx wrote: 
Hi everyone,
 
Happy New Year! Well, to start off the new year, I have a question on what the 
“curb” is in the LV-H report. The placement of the information, and the fact 
that it has an area and U-value (much the way the window frame does) leads me to 
believe it may be to account for Edge-of-Glass effects (if you look at Window5 
outputs it has COG U-values, frame U-values and edge-of-glass U-values).
 
I can’t see anywhere in the detailed edit mode to input curb information - I 
looked in both the “Glass Type Properties” and “Window Properties” Screens.
 
I found the following info in the DOE2 help file, but it looks like it only 
applies to skylights? It also wasn’t clear if it was in fact for edge of glass, 
and how to add this information (I’m guessing in the INP file?). Thanks for any 
help.
 
CURB -CONDUCT
Conductance of the skylight curb, excluding the outside air film but including 
the inside air film. 

Notes:
1.     You can define curbs only for exterior windows and skylights, not for 
interior windows.
2.     If the CURB-HEIGHT is zero no curb calculations will be performed.
3.     The curb area is not subtracted from the associated exterior wall area.
4.     Each hour, the program adds the effect of a wind speed-dependent outside 
air film to the user specified CURB-CONDUCT.
5.     The various elements of a curb (top, bottom, side, dividers, etc.) may 
have different conductances. In this case, CURB-CONDUCT should be an 
area-weighted average of the different elements.
6.     The program finds the overall window conduction by adding curb, frame, 
edge-of-glass, and center-of-glass contributions. Thus, all three of these 
contributions are included in each of the following report quantities:
          "Window Conduction" in summary reports LS-B, LS-C, LS-E, and LS-F;
          "Window U-Value" and "Window Area" in verification report LV-D and 
LV-H;
          WINDOW hourly report variable #1, "Window U-Value".
7.     A WINDOW multiplier also multiplies the curb area.
8.     Window fins and overhangs shade the curb as well as the glazing.
9.     Shading devices, like blinds and drapes, that you specify using the 
WINDOW keywords SHADING-SCHEDULE and CONDUCT-SCHEDULE, affect only the glazed 
part of the window. They do not affect the heat conduction through the curb.
10.   If the window has a setback, the curb is also set back by the same amount.
 
Kind regards,
Alex Krickx
 
Alex Krickx, LEED AP
Building Energy Specialist
Error! Filename not specified.
1250 Elko Dr, Sunnyvale, CA 94089
(t) 408.541.8124
 
Warning: The information contained in this e-mail may be privileged 
attorney-client communications or attorney work product and/or proprietary and 
confidential.  If the reader of this message is not the intended recipient then 
you have received it in error and any review, distribution or copying of this 
message is prohibited and you are to notify us immediately by reply e-mail and 
delete the original message immediately.
 
 
  
_______________________________________________
Equest-users mailing list
http://lists.onebuilding.org/listinfo.cgi/equest-users-onebuilding.org
To unsubscribe from this mailing list send  a blank message to 
EQUEST-USERS-UNSUBSCRIBE at ONEBUILDING.ORG

_______________________________________________ Equest-users mailing list 
http://lists.onebuilding.org/listinfo.cgi/equest-users-onebuilding.org To 
unsubscribe from this mailing list send a blank message to 
EQUEST-USERS-UNSUBSCRIBE at ONEBUILDING.ORG 



      
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/equest-users-onebuilding.org/attachments/20110105/4391f690/attachment-0001.htm>