[Equest-users] DX Cooling Option

[Eric Hethcoat]

Checked all schedules first.  All are the same.
 
Went back into the Wizard.  It was selected as furnace with no cooling.
Changed to furnace with DX as a PSZ.  reran the file and again same
result.  I presume that if any cooling shows, then it is indeed modeling
it - correctly?  
 
The space with no cooling is identical in all but physical size to the
other spaces that do have a cooling load associated to them in the
simulation output.

Eric

________________________________

From: Nick Caton [mailto:ncaton at smithboucher.com] 
Sent: Thursday, June 14, 2012 4:52 PM
To: Eric Hethcoat; equest-users at lists.onebuilding.org
Subject: RE: DX Cooling Option



Hi Eric,


First thought is if you chose "no cooling" in the wizards, the wizards
may have assigned a system type (there are many) which cannot be
assigned any cooling function no matter what you do.  You may need to
review and re-assign the system type as a result.


If this could be the case and you're still gaining familiarity, it can
be instructive to save a 'dummy' copy of your project, then go back to
wizards, re-create the system you're thinking of (with cooling), and
observe what the wizards generate as a result for edits in your 'actual'
project.

 

If the system is correctly defined, an easy miss might be defining
cooling thermostat inputs (scheduling) for the zones to be conditioned.

 

Best of luck!

 

~Nick

 

 

NICK CATON, P.E.

SENIOR ENGINEER

 

Smith & Boucher Engineers

25501 west valley parkway, suite 200

olathe, ks 66061

direct 913.344.0036

fax 913.345.0617

www.smithboucher.com 

 

From: equest-users-bounces at lists.onebuilding.org
[mailto:equest-users-bounces at lists.onebuilding.org] On Behalf Of Eric
Hethcoat
Sent: Thursday, June 14, 2012 4:17 PM
To: equest-users at lists.onebuilding.org
Subject: [Equest-users] DX Cooling Option

 

I've got a baseline and proposed model for a project set up.  I've been
thru every wizard mode input, then changed several items in the detailed
input mode.  Successful runs for both.  

 

The one thing that is not showing up on only a single zone for one
system between both models is cooling.  In the wizard mode - it is
entered as "no cooling".  I understand this limits what systems can be
chosen - in wizard mode.

 

In the detailed mode I've been thru every cooling tab to ensure all
cooling properties are correctly indicated as if we had DX - however
under the air-side system tab, the selection of chilled water or DX is
not available - and is greyed out to N/A.  I've played with zone temps,
schedules, etc. and none have any change in the result for cooling in
this area.

 

How can I ensure that I have the proper cooling?  I only have standard
gas fired heating/DX cooling PSZ equipment.  No heat pump.  

 

Eric Hethcoat, P.E.

Partner

Latimer, Sommers & Associates, P.A.

3639 SW Summerfield Dr., Suite A

Topeka, KS  66614

c.  913.481.3256

w.  785.233.3232

f.  785.233.0647

ehethcoat at lsapa.com

 

This message and any attachments included here-in, are solely for the
intended recipient and may contain confidential or privileged
information.  If you are not the intended recipient, any review,
disclosure, copying, use, forwarding, or distribution of the information
included in this message and any attachments is prohibited.  If you have
received this communication in error, please notify the sender by reply
e-mail and immediately and permanently delete this message and any
attachments.  Thank you.

 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/equest-users-onebuilding.org/attachments/20120614/ce765d9c/attachment-0002.htm>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: image/jpeg
Size: 1459 bytes
Desc: image001.jpg
URL: <http://lists.onebuilding.org/pipermail/equest-users-onebuilding.org/attachments/20120614/ce765d9c/attachment-0002.jpeg>