[Equest-users] Simulation Run Terminates when generating reports

[Amruta Khanolkar]

it is based on the position of your fan. Check if it is "draw through" or
"blow through" fan and accordingly calculate your coil temp. Your supply
temperature should be 6-8 deg. higher than your coil temp.
Amruta Khanolkar

*Amruta Khanolkar*
Mechanical Engineering
……………………………………………………

*SmithGroupJJR*
Arizona Center, 455 North Third St., Suite 250
Phoenix, AZ 85004
*
**t* 602.265.2200 *d* 602.824.5273 *f* 734.780.8787

Amruta.Khanolkar at smithgroupjjr.com<https://email.smithgroupjjr.com/owa/redir.aspx?C=g8EbtpTjeUmYu31NPgrqjSdwWKhA1c8Ib9DKevcVJ09Mf3l-inzHoDtkjuxqNkwQPbnjOR8y8dk.&URL=mailto%3aAmruta.Khanolkar%40smithgroupjjr.com>





On Fri, Feb 1, 2013 at 1:20 PM, Sami, Vikram <Vikram.Sami at perkinswill.com>wrote:

> I would check your coil temps, and also make sure your supply air temp is
> sufficiently higher than your coil temp. ****
>
> ** **
>
> * *
>
> *Vikram Sami*, LEED AP BD+C****
>
> Sustainable Design Analyst****
>
> 1315 Peachtree St. NE, Atlanta, GA 30309****
>
> t: 404-443-7462    f: 404.892.5823       e: vikram.sami at perkinswill.com
> www.perkinswill.com****
>
> *Perkins+Will.*  Ideas + buildings that honor the broader goals of society
> ****
>
> ** **
>
> ** **
>
> *From:* equest-users-bounces at lists.onebuilding.org [mailto:
> equest-users-bounces at lists.onebuilding.org] *On Behalf Of *Mike Raiva
> *Sent:* Friday, February 01, 2013 1:08 PM
> *To:* John Aulbach
> *Cc:* equest-users at lists.onebuilding.org
>
> *Subject:* Re: [Equest-users] Simulation Run Terminates when generating
> reports****
>
> ** **
>
> Here is the error that I getting.****
>
> ** **
>
>
> ***ERROR***********************************************************************
> ****
>
>              In EL1 Sys7 (VAVS) (G.WSW16)       , cooling coil leaving
> temperature must****
>
>              be at least 6F higher than entering water temp.****
>
> ** **
>
> ** **
>
> *MICHAEL RAIVA, **P.Eng., LEED® AP*****
>
> *Mechanical*
>
> ** **
>
> *Williams Engineering Canada Inc.*
>
> *T:*  778.484.2983    *F:*  778.484.3901****
>
> *W:*  williamsengineering.com <http://www.williamsengineering.com>****
>
> * *
>
> *Engage.  Innovate.  Inspire.*
>
> * *
>
> *Please consider the environment before printing this email.*
>
> *Email Transmission Policy* <http://www.williamsengineering.com/legal>****
>
> ** **
>
> *From:* John Aulbach [mailto:jra_sac at yahoo.com]
> *Sent:* Friday, February 01, 2013 9:59 AM
> *To:* Mike Raiva
> *Subject:* Re: [Equest-users] Simulation Run Terminates when generating
> reports****
>
> ** **
>
> Sir:
>
> Have you tried hitting the Detail Output button? Many times, it will list
> your errors.
>
> John R. Aulbach, PE****
>
> ** **
>
> ** **
> ------------------------------
>
> *From:* Mike Raiva <mraiva at williamsengineering.com>
> *To:* "equest-users at lists.onebuilding.org" <
> equest-users at lists.onebuilding.org>
> *Sent:* Friday, February 1, 2013 9:54 AM
> *Subject:* [Equest-users] Simulation Run Terminates when generating
> reports****
>
> ** **
>
> I am getting my model to simulate performance. However, it’s terminating
> when producing Summary and Verification reports with the following error
> shown below.****
>
>  ****
>
> Is there a way to trace where the error is?****
>
>  ****
>
> Thank you.****
>
>  ****
>
> ****
>
>  ****
>
> *MICHAEL RAIVA, **P.Eng., LEED® AP*****
>
> *Mechanical*****
>
>  ****
>
> *Williams Engineering Canada Inc.*****
>
> *T:*  778.484.2983    *F:*  778.484.3901****
>
> *W:*  williamsengineering.com <http://www.williamsengineering.com/>****
>
> * *****
>
> *Engage.  Innovate.  Inspire.*****
>
> * *****
>
> *Please consider the environment before printing this email.*****
>
> *Email Transmission Policy* <http://www.williamsengineering.com/legal>****
>
>  ****
>
>
> _______________________________________________
> Equest-users mailing list
> http://lists.onebuilding.org/listinfo.cgi/equest-users-onebuilding.org
> To unsubscribe from this mailing list send  a blank message to
> EQUEST-USERS-UNSUBSCRIBE at ONEBUILDING.ORG****
>
> _______________________________________________
> Equest-users mailing list
> http://lists.onebuilding.org/listinfo.cgi/equest-users-onebuilding.org
> To unsubscribe from this mailing list send  a blank message to
> EQUEST-USERS-UNSUBSCRIBE at ONEBUILDING.ORG
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/equest-users-onebuilding.org/attachments/20130202/2d902816/attachment-0002.htm>