[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [EnergyPlus_Support] Re: Multiple chillers
Please send your input data file (idf) to the EnergyPlus helpdesk at http://energyplus.helpserve.com
You'll also need to specify which version of EnergyPlus you are using to perform the simulations... and please indicate which weather file you are using.
The definitions of the output variables are provided in the EnergyPlus Input Output Reference. Differences between Plant Loop Cooling Demand [W] and Chiller Evap Heat Trans Rate [W] (for all four chillers) could be due to unmet loads (e.g., the chillers were unable to meet the loop chilled water set point temperature, or the chillers overcooled the loop below the set point temperature because of some of your inputs).
beyangj wrote:
> Dear All,
>
> I¡¯d like to explain more about the questions.
>
> For example, PlantLoopCoolingDemand:HVAC, namely the Total Water
> Cooling Coil Energy of all zones, is 2272.7kw, but all the 4 chillers
> operated at the same Chiller Part Load Ratio 0.425, and Chiller Evap
> Heat Trans Rate for every chiller is 586.3kw, the full load chiller
> capacity for every chiller is 1512 kw in this model. According to the
> reality, only two chillers can provide the system cooling demand
> 2272.7kw, why the 4 chillers operate together? The sum of the Chiller
> Evap Heat Trans Rate of the 4 chillers (2345.6 kw) are not equal to
> the system cooling demand 2272.7kw. What make the difference? The Load
> Distribution Scheme is set as Sequential.
>
> According to the report variable for Chiller Evap Heat Trans Rate and
> Chiller Part Load Ratio, the value of Chiller Evap Heat Trans Rate
> over Chiller Part Load Ratio is not equal to the maximum chiller
> capacity, why this happened? Chiller Evap Heat Trans Rate is the
> chiller capacity? Why the Chiller Evap Water Outlet Temp[C] is not 7¡æ
> as expected?
>
> In addition, CHILLED WATER LOOP CHILLED WATER LOOP:Plant Loop Cooling
> Demand is 7730.5kw, CHILLED WATER LOOP CHILLED WATER LOOP:Plant Loop
> Unmet Demand is 175.3kw. Why the Plant Loop Unmet Demand is not zero?
> The Minimum Unloading Ratio is set as 0.25. What¡¯s the relationship
> between the Plant Loop Cooling Deman and the Total Water Cooling Coil
> Energy of all zones?
>
>
> I appreciate your help!
>
> Young
>
>
>
>
>
> --- In EnergyPlus_Support@xxxxxxxxxxxxxxx, "beyangj" <beyangj@...> wrote:
>
>> Dear all,
>>
>> I have some questions about the model of multiple chillers. There are
>> four water-cooled centrifugal chillers in the model, and their
>> capacity are the same. The chillers are controlled as SEQUENTIAL.
>>
>> The first question is what's the relationship between Plant Loop
>> Cooling Demand [W] and Chiller Evap Heat Trans Rate [W]? When I change
>> the reference capacity in Chiller:Electric:EIR, the Plant Loop Cooling
>> Demand[W] also changed, why this happened?
>>
>>
>> The second question is that the Reference Leaving Chilled Water
>> Temperature is set as 7¡æ, and Leaving Chilled Water Lower Temperature
>> Limit is set as 5¡æ. But in the outputs, the Chiller Evap Water Outlet
>> Temp[C] is 5¡æ in all outdoor conditions, why the Chiller Evap Water
>> Outlet Temp[C] is not 7¡æ as expected?
>>
>> When the cooling capacity of three chillers satisfied the cooling
>> demand, but all the 4 chillers operated, and all the chiller operated
>> on low part load ratio, even all less than 0.3, and Chiller Evap Heat
>> Trans Rate [W] of the first three chillers are the same, why no
>> chillers can operate at full load capacity? And why the fourth chiller
>> operates even there is no need for it to operate? If three chillers
>> can provide enough cooling capacity, they can operate at even load
>> sharing without operating the 4th chiller?
>>
>>
>> Thanks in advance.
>>
>>
>> Young
>>
------------------------------------
The primary EnergyPlus web site is found at:
http://www.energyplus.gov
The group web site is:
http://groups.yahoo.com/group/EnergyPlus_Support/
Attachments are not allowed -- please post any files to the appropriate folder in the Files area of the Support Web Site.
EnergyPlus Documentation is searchable. Open EPlusMainMenu.pdf under the Documentation link and press the "search" button.
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/EnergyPlus_Support/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/EnergyPlus_Support/join
(Yahoo! ID required)
<*> To change settings via email:
mailto:EnergyPlus_Support-digest@xxxxxxxxxxxxxxx
mailto:EnergyPlus_Support-fullfeatured@xxxxxxxxxxxxxxx
<*> To unsubscribe from this group, send an email to:
EnergyPlus_Support-unsubscribe@xxxxxxxxxxxxxxx
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/