[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [EnergyPlus_Support] LEED template and Energyplus





Thanks a lot for your answers.

é?©æ??, Alvaro, and Oscar.


On Thu, Jun 21, 2012 at 4:53 AM, oscar hernandez <oscarhernandez_81@xxxxxxxxxxx> wrote:
 

The allsummary repport gives you the end uses and the peak energy, take the csv output file and youare going to find this.

Oscar.


To: EnergyPlus_Support@xxxxxxxxxxxxxxx
From: alvaro.urrutia@xxxxxxxxx
Date: Wed, 20 Jun 2012 14:53:22 -0700

Subject: Re: [EnergyPlus_Support] LEED template and Energyplus

 

I used Demand End Use Components Summary for LEED Documentation (according energyplus documentation), but in a recent project, the reviewer team has send me a observation about this issue, because the Demand End Uses Components Summary Plots demand in peak time for each energy source. (not by end uses separatedly). this situation becomes particularly unpleasant when,by example,  a project uses electricity for heating and cooling and then the peak time is only showed for heating time or only cooling time (wichever is greater).
For address this issue i use the Output Table: Summary Reports: PeakEnergyEndUseElectricityPart1Monthly, PeakEnergyEndUseElectricityPart2Monthly, PeakEnergyEndUseNaturalGasMonthly, PeakEnergyEndUseDieselMonthly, etc.
I hope I hope my explanation will be helpful.
 
Alvaro Urrutia Astorga
Energy modeler
POCH S.A.
Chile
 
From: Vinay Devanathan <vinay.devanathan@xxxxxxxxx>
To: EnergyPlus_Support@xxxxxxxxxxxxxxx
Sent: Wednesday, June 20, 2012 1:24 PM
Subject: Re: [EnergyPlus_Support] LEED template and Energyplus

 
Thank you.

I use this report summary, but I am seeing an unusual result this time.

The time of peak has shifted from 06:00 hours on Feb 2 to 00:00 hours on feb 2 on the 270 degree orientation alone. The 0, 90, 180 orientations have the time of peak as same 06:00 hours on Feb 2. The heating energy consumption stays very close to what it is in other orientations, but I am not sure how the peak would get shifted by changing the orientation. The South and North sides are glazed, maybe there is a difference in glazing % between the two cases, but I am not sure how it will affect HEATING at 00:00 and 06:00 hours...The boiler gas consumption output is very very similar on two cases. I hope someone has an answer to this situation. Thank you.

Vinay

On Wed, Jun 20, 2012 at 10:08 AM, é?©æ?? <foolishstar@xxxxxxx> wrote:
 
Demand End Use Components Summary  



At 2012-06-20 21:54:44,"Vinay Devanathan" <vinay.devanathan@xxxxxxxxx> wrote:
 
Hello All,

While filling out the LEED template Section 1.6, where do you get the Peak Demand numbers from in the EnergyPlus reports.

Look forward to hearing from someone soon. Thank you.

Vinay






--
Vinay Dev







--
Vinay Dev



__._,_.___


Primary EnergyPlus support is found at:
http://energyplus.helpserve.com or send a message to energyplus-support@xxxxxxxx

The primary EnergyPlus web site is found at:
http://www.energyplus.gov

The group web site is:
http://groups.yahoo.com/group/EnergyPlus_Support/

Attachments are currently allowed but be mindful that not everyone has a high speed connection.  Limit attachments to small files.

EnergyPlus Documentation is searchable.  Open EPlusMainMenu.pdf under the Documentation link and press the "search" button.




Your email settings: Individual Email|Traditional
Change settings via the Web (Yahoo! ID required)
Change settings via email: Switch delivery to Daily Digest | Switch to Fully Featured
Visit Your Group | Yahoo! Groups Terms of Use | Unsubscribe

__,_._,___