Re: [EnergyPlus_Support] Decrease in Cooling after Increasing WWR

[Jeremiah Crossett <jcrossett@xxxxxxxxxxxxxxx>]

I was recently schooled on this subject- due to a comment I made on the eQuest forums- the modeler was having a similar issue to yours and the chiller objects in Energy Plus are the same so the problem may also be: Check your part load chiller curve- it may be possible that the curve causes your system to run more efficiently with the higher load. Another way to check your model would be to check your solar gains and make sure they are higher with larger WWR.

Jeremiah D. Crossett  | Senior Analyst  |  Phase Change Energy Solutions

120 E. Pritchard St.  | Asheboro, NC 27203  | Mobile 503-688-8951

www.phasechange.com 

 

  

On Thu, Aug 16, 2012 at 1:09 AM, Ng Poh Khai <ng_khai@xxxxxxxxxxx> wrote:

 

Dear All,
 
I have a problem here.  I compared the cooling loads of a building with 0%WWR, 50%WWR and 100%WWR and got the results that the cooling load decreases sa the WWR increase.  I am located in a tropical country and this should actually not happen.  I have checked the constructions but it does not seem that anything is wrong.
 
The construction details are:
 
External Wall (default construction from sketchup):
 
! <Construction>,Construction Name,#Layers,#CTFs,Time Step {hours},ThermalConductance {w/m2-K},OuterThermalAbsorptance,InnerThermalAbsorptance,OuterSolarAbsorptance,InnerSolarAbsorptance,Roughness
! <Material>,Material Name,Thickness {m},Conductivity {w/m-K},Density {kg/m3},Specific Heat {J/kg-K},ThermalResistance {m2-K/w}
! <Material:Air>,Material Name,ThermalResistance {m2-K/w}
 Construction,EXTERIOR WALL,   5,  16,   0.167,     0.4586    ,   0.900,   0.900,   0.700,   0.700,MediumRough
 Material,M01 100MM BRICK,  0.1016,         0.890,   1920.000,      790.000,  0.1142   
 Material,M15 200MM HEAVYWEIGHT CONCRETE,  0.2032,         1.950,   2240.000,      900.000,  0.1042   
 Material,I02 50MM INSULATION BOARD,  0.0508,         0.030,     43.000,     1210.000,   1.693   
 Material:Air,F04 WALL AIR SPACE RESISTANCE,  0.1500   
 Material,G01A 19MM GYPSUM BOARD,  0.0190,         0.160,    800.000,     1090.000,  0.1187
 
Window Glazing:
 
! <WindowConstruction>,Construction Name,#Layers,Roughness,Conductance {W/m2-K},SHGC,Solar Transmittance at Normal Incidence,Visible Transmittance at Normal Incidence
! <WindowMaterial:Glazing>, Material Name, Optical Data Type, Spectral Data Set Name, Thickness {m}, Solar Transmittance,Front Solar Reflectance, Back Solar Reflectance, Visible Transmittance, Front Visible Reflectance,Back Visible Reflectance,Infrared Transmittance, Front Thermal Emissivity, Back Thermal Emissivity,Conductivity {W/m-K},Dirt Factor,Solar Diffusing
! <WindowMaterial:Gas>,Material Name,GasType,Thickness {m}
 WindowConstruction,EXTERIOR WINDOW,   1,VerySmooth,   2.141,   0.125,   0.051,   0.074
 WindowMaterial:Glazing,SPEAR TECHONOLOGY,SpectralAverage,,  0.03491,  0.05048,  0.77453,  0.77453,  0.07340,  0.21158,  0.37284,
 
Can anyone help me with this?  I have been stuck with this for a week now... I do not mind sending my idf files over if someone is able to take a quick look for me.
 
Any help or advice will be kindly appreciated.
 
Best Regards,
Poh Khai

__._,_.___

Primary EnergyPlus support is found at:
http://energyplus.helpserve.com or send a message to energyplus-support@xxxxxxxx

The primary EnergyPlus web site is found at:
http://www.energyplus.gov

The group web site is:
http://groups.yahoo.com/group/EnergyPlus_Support/

Attachments are currently allowed but be mindful that not everyone has a high speed connection.  Limit attachments to small files.

EnergyPlus Documentation is searchable.  Open EPlusMainMenu.pdf under the Documentation link and press the "search" button.

Your email settings: Individual Email|Traditional
Change settings via the Web (Yahoo! ID required)
Change settings via email: Switch delivery to Daily Digest | Switch to Fully Featured
Visit Your Group | Yahoo! Groups Terms of Use | Unsubscribe

__,_._,___