[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[EnergyPlus_Support] Re: Temperatures in a water loop
There are no bypass branches.
First part of the loop: <http://oi61.tinypic.com/ip1jdx.jpg>http://oi61.tinypic.com/ip1jdx.jpg
Second part: <http://oi62.tinypic.com/2s7ujrd.jpg>http://oi62.tinypic.com/2s7ujrd.jpg
Regards
---In EnergyPlus_Support@xxxxxxxxxxxxxxx, <jeannieboef@...> wrote :
Did you consider bypass branches?
Mit freundlichen Grü�en- Sent from my iPhone (excuse the brevity)
i. A.
Jean Marais
b.i.g. bechtold
Tel. +49 30 6706662-23
> On 20.03.2014, at 12:38, <<mailto:fpasserini.tn@...>fpasserini.tn@...> wrote:
>
>
> Iâ??m modeling a DHW loop.
>
> PlantLoop,
> DHW Loop, !- Name
> WATER, !- Fluid Type
> , !- User Defined Fluid Type
> DHW Loop Operation, !- Plant Equipment Operation Scheme Name
> Water Heater Use Loop Outlet Node, !- Loop Temperature Setpoint Node Name
> 100, !- Maximum Loop Temperature {C}
> 3, !- Minimum Loop Temperature {C}
> 0.00000283, !- Maximum Loop Flow Rate {m3/s}
> 0, !- Minimum Loop Flow Rate {m3/s}
> 0.015, !- Plant Loop Volume {m3}
> Water Heater Use Loop Inlet Node, !- Plant Side Inlet Node Name
> Water Heater Use Loop Outlet Node, !- Plant Side Outlet Node Name
> Water Heater Use Branches, !- Plant Side Branch List Name
> Water Heater Use Connectors, !- Plant Side Connector List Name
> Demand Inlet Node, !- Demand Side Inlet Node Name
> Demand Outlet Node, !- Demand Side Outlet Node Name
> Demand Branches, !- Demand Side Branch List Name
> Demand Connectors, !- Demand Side Connector List Name
> OPTIMAL; !- Load Distribution Scheme
>
> The water temperature delivered by the municipality is modeled as constantly equal to 15°C:
>
> Site:WaterMainsTemperature,
> Schedule, !- Calculation Method
> temp15C; !- Temperature Schedule Name
>
> Schedule:Compact,
> temp15C, !- Name
> Temperature, !- Schedule Type Limits Name
> Through: 12/31, !- Field 1
> For: AllDays, !- Field 2
> Until: 24:00, 15; !- Field 4
>
> As I would expect, when there is water flow the temperature of the â??Demand Side Outlet Nodeâ?? (Demand Outlet Node) is equal to 15°C: <http://oi60.tinypic.com/2mnq0km.jpg><http://oi60.tinypic.com/2mnq0km.jpg>http://oi60.tinypic.com/2mnq0km.jpg
>
> Among the output data, the water temperature of the â??Plant Side Inlet Nodeâ?? (Water Heater Use Loop Inlet Node) is much higher: <http://oi60.tinypic.com/5zgv9i.jpg><http://oi60.tinypic.com/5zgv9i.jpg>http://oi60.tinypic.com/5zgv9i.jpg
>
> I donâ??t understand why the temperature in the â??Plant Side Inlet Nodeâ?? is higher than the temperature in the â??Demand Side Outlet Nodeâ??. There is no element between them.
> I have found in the .bnd file:
> Plant Loop Return Connection,DHW LOOP,DEMAND OUTLET NODE,WATER HEATER USE LOOP INLET NODE
>
> The water heater is on the supply side and its setpoint temperature is 40°C. No recirculation should occur.
>
> WaterHeater:Mixed,
> Water Heater, !- Name
> 0.1, !- Tank Volume {m3}
> RISC Temp Schedule, !- Setpoint Temperature Schedule Name
> 0, !- Deadband Temperature Difference {deltaC}
> 61, !- Maximum Temperature Limit {C}
> Cycle, !- Heater Control Type
> 1200, !- Heater Maximum Capacity {W}
> , !- Heater Minimum Capacity {W}
> , !- Heater Ignition Minimum Flow Rate {m3/s}
> , !- Heater Ignition Delay {s}
> Electricity, !- Heater Fuel Type
> 1, !- Heater Thermal Efficiency
> , !- Part Load Factor Curve Name
> , !- Off Cycle Parasitic Fuel Consumption Rate {W}
> , !- Off Cycle Parasitic Fuel Type
> , !- Off Cycle Parasitic Heat Fraction to Tank
> , !- On Cycle Parasitic Fuel Consumption Rate {W}
> , !- On Cycle Parasitic Fuel Type
> , !- On Cycle Parasitic Heat Fraction to Tank
> Zone, !- Ambient Te
__._,_.___
Primary EnergyPlus support is found at:
<http://energyplus.helpserve.com>http://energyplus.helpserve.com or send a message to energyplus-support@xxxxxxxx
The primary EnergyPlus web site is found at:
<http://www.energyplus.gov>http://www.energyplus.gov
The group web site is:
<http://groups.yahoo.com/group/EnergyPlus_Support/>http://groups.yahoo.com/group/EnergyPlus_Support/
Attachments are currently allowed but be mindful that not everyone has a high speed connection. Limit attachments to small files.
EnergyPlus Documentation is searchable. Open EPlusMainMenu.pdf under the Documentation link and press the "search" button.
<http://geo.yahoo.com/serv?s=97476590/grpId=3387488/grpspId=1705007389/msgId=31596/stime=1395911457>
<https://groups.yahoo.com/neo/groups/EnergyPlus_Support/info;_ylc=X3oDMTJlajh1YTFqBF9TAzk3MzU5NzE0BGdycElkAzMzODc0ODgEZ3Jwc3BJZAMxNzA1MDA3Mzg5BHNlYwN2dGwEc2xrA3ZnaHAEc3RpbWUDMTM5NTkxMTQ1Nw-->Visit Your Group
* <https://groups.yahoo.com/neo/groups/EnergyPlus_Support/members/all;_ylc=X3oDMTJmNnU4bzA5BF9TAzk3MzU5NzE0BGdycElkAzMzODc0ODgEZ3Jwc3BJZAMxNzA1MDA3Mzg5BHNlYwN2dGwEc2xrA3ZtYnJzBHN0aW1lAzEzOTU5MTE0NTc->New Members 9
<https://groups.yahoo.com/neo;_ylc=X3oDMTJkYmc5bWcwBF9TAzk3NDc2NTkwBGdycElkAzMzODc0ODgEZ3Jwc3BJZAMxNzA1MDA3Mzg5BHNlYwNmdHIEc2xrA2dmcARzdGltZQMxMzk1OTExNDU3><http://l.yimg.com/ru/static/images/yg/img/email/new_logo/logo-groups-137x15.png>
? <https://info.yahoo.com/privacy/us/yahoo/groups/details.html>Privacy ? <mailto:EnergyPlus_Support-unsubscribe@xxxxxxxxxxxxxxx?subject=Unsubscribe>Unsubscribe ? <https://info.yahoo.com/legal/us/yahoo/utos/terms/>Terms of Use
__,_._,___