Thank you Javed!
I haven’t reviewed the file yet. That is my weekend project.
Christopher R. Jones,
P.Eng.
Technical Specialist
Sustainability & Energy
T +1 416-644-0252
2300 Yonge Street, Suite 2300
Toronto, ON M4P 1E4 Canada
Please consider the environment before printing...
From: EnergyPlus_Support@xxxxxxxxxxxxxxx [mailto:EnergyPlus_Support@xxxxxxxxxxxxxxx]
Sent: Wednesday, December 06, 2017 11:49 AM
To: EnergyPlus_Support@xxxxxxxxxxxxxxx
Subject: Re: [EnergyPlus_Support] RE: EnergyPlus - DOAS, radiant infloor heating and PTAC
Hello Chris,
here you find
one zone sample model with a DOAS (with heating Coil, HX)+ Radiant heating (served by Boiler)+ PTAC system. This will give you fair idea about equipment and Branch connections. I am not sure how your design varies from this arrangement such as
heat recovery, preheat coil etc. But it's worth checking the temperature set point in your model in order to make it aligned with the design model. I have done some quality checks on each node to check if set-point manager works fine. I have used San Francisco
weather file to do some more sanity checks.
P.S It took me roughly 60 mins to make some modifications in the example files to develop this sample model including basic quality checks.
Hope this helps!!
On Mon, Dec 4, 2017 at 11:00 PM, 'Jones, Christopher'
christopher.r.jones@xxxxxxx [EnergyPlus_Support] <EnergyPlus_Support@xxxxxxxxxxxxxxx> wrote:
Thank you very much. I am not so worried about adding the PTACs � cooling only but I am worried about removing the underfloor radiant cooling � chiller, loop, branches, coils, splitters, ettc. The “merged” system would be DOAS Underfloor heating and PTAC cooling.
Christopher R. Jones, P.Eng.
Technical Specialist
Sustainability & Energy
Please consider the environment before printing...
From: EnergyPlus_Support@xxxxxxxxxxxxxxx [mailto:EnergyPlus_Support@xxxxxxxxxxxxxxx]
Sent: Monday, December 04, 2017 2:27 PM
To: EnergyPlus_Support@xxxxxxxxxxxxxxx
Subject: [EnergyPlus_Support] Re: EnergyPlus - DOAS, radiant infloor heating and PTAC
As a pointer for you, the PTAC system is a zone system so I would use the DOAS with radiant floor as your base file and add in the PTAC (also radiant floor files have all sorts of extras in them to do with surfaces and all sorts so this really should be your base file). You can add it in directly, just make sure you take all the components associated with the PTAC. ALL the components, that is the PTAC, the hot and cold coils, the fans, the branches, the outdoor air mixer, outdoor air equipment list, go all the way down and make sure you pick up everything
The gotchas will be at Equipment list and equipment connections. You can only have one equipment list and one equipment connections per zone.
Equipment List: You will have to add PTACs to your existing equipment lists.
Equipment Connections: you need add the exhaust node you have in the PTAC file to the existing equipment connections for the correct zones. You will need to make a nodelist (a separate object) for each zone that has a PTAC and a DOAS connection and in this list put the two node names that are in the inlet node in the equipment connection objects. Then add this new nodelist name to your node connections
Depending on whether the PTAC has hot and cold water coils means you will need to add these onto the branchlist, the splitter and the connector (essentially adding them into the chiller and boiler loops)
And that should do it. Happy to help some more if you get stuck
Annie
From: EnergyPlus_Support@xxxxxxxxxxxxxxx <EnergyPlus_Support@xxxxxxxxxxxxxxx> on behalf of 'Jones, Christopher' christopher.r.jones@xxxxxxx [EnergyPlus_Support] <EnergyPlus_Support@xxxxxxxxxxxxxxx>
Sent: 03 December 2017 19:35
To: EnergyPlus_Support@xxxxxxxxxxxxxxx
Subject: [EnergyPlus_Support] EnergyPlus - DOAS, radiant infloor heating and PTAC
Hello,
I am looking for an example .idf � DOAS, radiiant infloor heating and packaged terminal air conditioners.
I have two models of my small building:
DOAS �� radiant infloor heating and cooling
DOAS � PTAC with ssupplemental hydronic heating.
I would like to “merge” these two files to end up with DOAS �radiant innfloor heating and PTAC. It seems to me like that could be a lot of “gotchas” trying to revise the two files � I have next to no experience editing EnergyPPlus file directly.
Any pointers? Anyone feel like looking at my two .idf files in order to offer hints?
Christopher R. Jones, P.Eng.
Technical Specialist
Sustainability & Energy
Please consider the environment before printing...
NOTICE: This communication and any attachments ("this message") may contain information which is privileged, confidential, proprietary or otherwise subject to restricted disclosure under applicable law. This message is for the sole use of the intended recipient(s). Any unauthorized use, disclosure, viewing, copying, alteration, dissemination or distribution of, or reliance on, this message is strictly prohibited. If you have received this message in error, or you are not an authorized or intended recipient, please notify the sender immediately by replying to this message, delete this message and all copies from your e-mail system and destroy any printed copies. You are receiving this communication because you are listed as a current WSP contact. Should you have any questions regarding WSP's electronic communications policy, please consult our Anti-Spam Commitment at www.wsp.com/casl. For any concern or if you believe you should not be receiving this message, please forward this message to caslcompliance@xxxxxxx so that we can promptly address your request. Note that not all messages sent by WSP qualify as commercial electronic messages.
AVIS : Ce message, incluant tout fichier l'accompagnant (« le message »), peut contenir des renseignements ou de l'information privilégiés, confidentiels, propriétaires ou à divulgation restreinte en vertu de la loi. Ce message est destiné à l'usage exclusif du/des destinataire(s) voulu(s). Toute utilisation non permise, divulgation, lecture, reproduction, modification, diffusion ou distribution est interdite. Si vous avez reçu ce message par erreur, ou que vous n'êtes pas un destinataire autorisé ou voulu, veuillez en aviser l'expéditeur immédiatement et détruire le message et toute copie électronique ou imprimée. Vous recevez cette communication car vous faites partie des contacts de WSP. Si vous avez des questions concernant la politique de communications électroniques de WSP, veuillez consulter notre Engagement anti-pourriel au www.wsp.com/lcap. Pour toute question ou si vous croyez que vous ne devriez pas recevoir ce message, prière de le transférer au conformitelcap@xxxxxxx afin que nous puissions rapidement traiter votre demande. Notez que ce ne sont pas tous les messages transmis par WSP qui constituent des messages electroniques commerciaux.
-LAEmHhHzdJzBlTWfa4Hgs7pbKl
--
Javed Iqbal, LEED AP, CEA
Sr. Energy Analyst
__._,_.___
Posted by: "Jones, Christopher" <Christopher.r.Jones@xxxxxxx>
EnergyPlus support is found at:
http://energyplus.helpserve.com or send a message to energyplus-support@xxxxxxxx
The EnergyPlus web site is found at:
http://www.energyplus.net/
The group web site is:
http://groups.yahoo.com/group/EnergyPlus_Support/
Attachments are currently allowed but be mindful that not everyone has a high speed connection. Limit attachments to small files.
EnergyPlus Documentation is searchable. Open EPlusMainMenu.pdf under the Documentation link and press the "search" button.
__,_._,___