I am running a model using EPLaunch. During the simulation, EnergyPlus throws errors in the cmd window. These errors are not included in the .err file. Is there a way to capture these errors to file?
Â
For example:
Â
Christopher R Jones, P.Eng.
T+ 1 416-644-0252
Â
Â
From: EnergyPlus_Support@xxxxxxxxxxxxxxx [mailto:EnergyPlus_Support@xxxxxxxxxxxxxxx]
Sent: Monday, November 12, 2018 10:05 AM
To: EnergyPlus_Support@xxxxxxxxxxxxxxx
Subject: Re: [EnergyPlus_Support] Discussion on EMS use in Energyplus on Opening factor ControlÂ
Â
your ems directly sets the component. perhaps you want to set the component as fully open in the idf and then manipulate the component's schedule instead with ems? from memory there are a couple of variables which are multiplied with each other to deturmine how open the window is.
Â
On Thu, 8 Nov 2018, 22:10 shahaohan@xxxxxxx [EnergyPlus_Support] <EnergyPlus_Support@xxxxxxxxxxxxxxx wrote:
Â
When I'm checking the simulation example in the energyplus, I found a EMS problem relating to the opening factor Control. In the
EMSAirflowNetworkOpeningControlByHumidity.idf, the example file shows a EMS control to the surface:Zn001:Wall001:Win001Â by humidity. At the same time, the example file set a venting availability schedule in the Zone Level to control the Opening time. The Venting schedule is below:Schedule:Compact, VentingSched, !- Name Fraction, !- Schedule Type Limits Name Through: 12/31, !- Field 1 For: AllDays, !- Field 2 Until: 7:00,1.0, !- Field 3 Until: 17:00,0.0, !- Field 5 Until: 24:00,1.0; !- Field 7
The EMS control code is below:
EnergyManagementSystem:Sensor, ZoneRH, !- Name Zone 1 Node, !- Output:Variable or Output:Meter Index Key Name System Node Relative Humidity; !- Output:Variable or Output:Meter Name
EnergyManagementSystem:Actuator, MyOpenFactor, !- Name Zn001:Wall001:Win001, !- Actuated Component Unique Name AirFlow Network Window/Door Opening, !- Actuated Component Type Venting Opening Factor; !- Actuated Component Control Type
EnergyManagementSystem:ProgramCallingManager, RH Controlled Open Factor, !- Name BeginTimestepBeforePredictor, !- EnergyPlus Model Calling Point RH_OpeningController; !- Program Name 1
EnergyManagementSystem:Program, RH_OpeningController, !- Name IF ZoneRH < 25, !- Program Line 1 SET MyOpenFactor = 0.0, !- Program Line 2 ELSEIF ZoneRH > 60, !- SET MyOpenFactor = 1.0, !- ELSE, !- SET MyOpenFactor = (ZoneRH - 25) / (60 - 25), !- ENDIF; !-
Then, when I checking the results, I found that the Venting availability Schedule is ignored by applying the EMS, which means users cannot control the opening factors based on time! Did anyone discover this irrational problem? Is this a Bug or error? How can user control the openings with EMS and time?
NOTICE: This communication and any attachments ("this message") may contain information which is privileged, confidential, proprietary or otherwise subject to restricted disclosure under applicable law. This message is for the sole use of the intended recipient(s). Any unauthorized use, disclosure, viewing, copying, alteration, dissemination or distribution of, or reliance on, this message is strictly prohibited.. If you have received this message in error, or you are not an authorized or intended recipient, please notify the sender immediately by replying to this message, delete this message and all copies from your e-mail system and destroy any printed copies. You are receiving this communication because you are listed as a current WSP contact. Should you have any questions regarding WSP's electronic communications policy, please consult our Anti-Spam Commitment at www.wsp.com/casl. For any concern or if you believe you should not be receiving this message, please forward this message to caslcompliance@xxxxxxx so that we can promptly address your request. Note that not all messages sent by WSP qualify as commercial electronic messages.
AVIS : Ce message, incluant tout fichier l'accompagnant (« le message »), peut contenir des renseignements ou de l'information privilégiés, confidentiels, propriétaires ou à divulgation restreinte en vertu de la loi. Ce message est destiné à l'usage exclusif du/des destinataire(s) voulu(s). Toute utilisation non permise, divulgation, lecture, reproduction, modification, diffusion ou distribution est interdite. Si vous avez reçu ce message par erreur, ou que vous n'êtes pas un destinataire autorisé ou voulu, veuillez en aviser l'expéditeur immédiatement et détruire le message et toute copie électronique ou imprimée. Vous recevez cette communication car vous faites partie des contacts de WSP. Si vous avez des questions concernant la politique de communications électroniques de WSP, veuillez consulter notre Engagement anti-pourriel au www.wsp.com/lcap. Pour toute question ou si vous croyez que vous ne devriez pas recevoir ce message, prière de le transférer au conformitelcap@xxxxxxx afin que nous puissions rapidement traiter votre demande. Notez que ce ne sont pas tous les messages transmis par WSP qui constituent des messages electroniques commerciaux.
-LAEmHhHzdJzBlTWfa4Hgs7pbKl--Javed Iqbal, LEED AP, CEASr. Energy AnalystÂ
__._,_.___
Posted by: Javed Iqbal <eee.javed@xxxxxxxxx>
EnergyPlus support is found at:
http://energyplus.helpserve.com or send a message to energyplus-support@xxxxxxxx
The EnergyPlus web site is found at:
http://www.energyplus.net/
The group web site is:
http://groups..yahoo.com/group/EnergyPlus_Support/
Attachments are currently allowed but be mindful that not everyone has a high speed connection. Limit attachments to small files.
EnergyPlus Documentation is searchable. Open EPlusMainMenu.pdf under the Documentation link and press the "search" button.
![]()
![Yahoo! Groups]()