[Equest-users] T24 Compliance model

[Carol Gardner]

I'd be willing to take a look if you want to zip up and send the .inp and
.pd2 files. BTW I used to work for Glumac in Portland.

Carol

On Fri, Jul 1, 2011 at 10:36 AM, Ross Farris <RFarris at glumac.com> wrote:

> I looked through both but the file I was referring to was the .bdl file. *
> ***
>
> ** **
>
> *Ross Farris *
>
> Energy Analyst****
>
> GLUMAC | 415.398.7667****
>
> ** **
>
> *From:* Carol Gardner [mailto:cmg750 at gmail.com]
> *Sent:* Friday, July 01, 2011 10:24 AM
> *To:* Ross Farris
> *Cc:* equest-users at lists.onebuilding.org
> *Subject:* Re: [Equest-users] T24 Compliance model****
>
> ** **
>
> Ross,
>
> Did you look in the output file with the .bdl extension on it or the one
> named bdlout?
>
> Carol****
>
> On Fri, Jul 1, 2011 at 9:50 AM, Ross Farris <RFarris at glumac.com> wrote:***
> *
>
> Hello all,****
>
>  ****
>
> I am currently working on an apartment building here in California and
> trying to run the T24 compliance portion of eQUEST. I have run into an error
> that I cannot solve and have not seen before in the past T24 compliance
> models our firm has completed. ****
>
>  ****
>
> There is a rules evaluation error that occurs and says: “Error Writing BDL
> standard File”   Which part of the BDL are we talking about here? Is there a
> way to check this? Within the eQUEST module it says there are no BDL errors
> if I click the little blue button with the red check mark next to the
> simulation buttons. ****
>
>  ****
>
> I looked through the BDL code and nothing stands out as I scroll through it
> until I get to the bottom. There are a bunch of warnings stating:
> *WARNING***Custom weighting factors cannot be calculated for SPACE****
>
>             S~zone-A6CO13 because it has furniture but no valid floor.
> ASHRAE****
>
>             weighting factors with floor weight of 70 lb/ft2 (342 kg/m2)
> will be****
>
>             used instead. If floor is an exterior wall, underground surface
> or****
>
>             interior wall defined in this space be sure tilt = 180. If
> floor is****
>
>             an interior wall defined in an adjacent space be sure tilt = 0.
> ****
>
>  ****
>
> There are one of these for each zone. However both my LEED model version
> for this project (which works fine) and our past compliance models have had
> the same warnings for each space. ****
>
>  ****
>
> Also in my problematic compliance model there are two “cautions” that
> state:****
>
> -CAUTION--------------------------------------------------------------------------------------NO
> HEATING EQUIPMENT HAS BEEN DEFINED   ****
>
> -CAUTION--------------------------------------------------------------------------------------NO
> COOLING EQUIPMENT HAS BEEN DEFINED   ****
>
>  ****
>
> These are also shown in my LEED version model even though it runs and
> calculates heating and cooling loads. However these “cautions” do not show
> up un our past compliance models. ****
>
>  ****
>
> I am thinking the caution about no heating and cooling equip is happening
> because the model stops computing before it gets the chance to compute the
> heating and cooling equip because it stops for some other reason prior to
> that. ****
>
>  ****
>
> I am kind of on a time crunch to get this completed so any thoughts,
> opinions or suggestions they are greatly appreciated. I would be happy to
> answer any further questions via email or phone and would be happy to send
> you my .inp file, .pd2 file and my .bdl file if you want to take a look
> yourself. ****
>
>  ****
>
> Thanks in advance. ****
>
>  ****
>
> Cheers,****
>
>  ****
>
>  ****
>
> *Ross Farris*
> Energy Analyst
>
> *Error! Filename not specified.* <http://www.glumac.com/>****
> ------------------------------
>
> 150 California Street, 3rd Floor
> San Francisco, CA 94111
> T.  415.398.7667 ext.4083  F. 415.398.0596
> *Thinking. Inside the building.*****
>
>  *Error! Filename not specified.* <http://twitter.com/GlumacEngineers>*Error!
> Filename not specified.* <http://www.linkedin.com/company/34034?trk=tyah>
>    ****
>
>  ****
>
>
> _______________________________________________
> Equest-users mailing list
> http://lists.onebuilding.org/listinfo.cgi/equest-users-onebuilding.org
> To unsubscribe from this mailing list send  a blank message to
> EQUEST-USERS-UNSUBSCRIBE at ONEBUILDING.ORG****
>
>
>
>
> --
> Carol Gardner PE****
>



-- 
Carol Gardner PE
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/equest-users-onebuilding.org/attachments/20110701/29aca818/attachment-0002.htm>