[TRNSYS-users] end of file error

David BRADLEY d.bradley at tess-inc.com
Fri Jun 12 12:49:14 PDT 2015


Suhrid,
   Usually what has happened in a situation like this is that you ran 
the simulation once in a new place and it didn't find a file that it was 
looking for. Unfortunately when TRNSYS doesn't find a file that it 
thinks should exist, it creates a blank one. Then the next time you run 
your sim, you get an "end of file" error.

   Check the location of the file and look at the file size; its 
probably 0KB. You can delete it and find the file in the original 
location and move it over.

   The best way to avoid problems like this is to always code the full 
path to the file in the external files tab (starting with the drive 
letter as in c:\Trnsys17\MyProjects\... etc.)
kind regards,
  David


On 06/11/2015 19:36, Suhrid A Deshmukh wrote:
> Hello,
>
> I was running my simulation just fine, and then I moved the location 
> of one of the input files that I was using to inside of the project 
> folder itself. Now I get an error that says this:
>
> "The end of the  input file was found before the END statement was found"
>
> Do you know what this means and how to fix this?
>
>
> Regards,
> Suhrid
>
>
> ------------------------------------------------------------------------
> *From:* TRNSYS-users [trnsys-users-bounces at lists.onebuilding.org] on 
> behalf of Angel Carrera [angel.carrera at aiguasol.coop]
> *Sent:* Thursday, June 11, 2015 5:06 AM
> *To:* TRNSYS users mailing list at OneBuilding. org
> *Subject:* Re: [TRNSYS-users] end of file error
>
> Suhrid,
>
> assuming that you are using type 53, I think the message does not 
> necessarily indicates what is the variable out of range, simply, that 
> the type is getting a COP either too big or too low for the data you 
> defined in the external performance file. Thus it might be either the 
> temperature difference, the chiller power or the electrical 
> consumption, wich are the data you input through the external file, best
>
> Angel
>
> El 11/06/2015 00:23, "Suhrid A Deshmukh" <suhrid at mit.edu 
> <mailto:suhrid at mit.edu>> escribió:
>
>     Hello David,
>
>     I am trying to include a chiller component into my TRNSYS model.
>     Get an error that says the Chiller might be operating outside the
>     acceptable range. Is this range the range of the cooling loads,
>     the temperatures etc? What exactly is it?
>
>     Regards,
>     Suhrid
>     ------------------------------------------------------------------------
>     *From:* David BRADLEY [d.bradley at tess-inc.com
>     <mailto:d.bradley at tess-inc.com>]
>     *Sent:* Tuesday, June 09, 2015 3:37 PM
>     *To:* Suhrid A Deshmukh; TRNSYS users mailing list at OneBuilding.org
>     *Subject:* Re: [TRNSYS-users] end of file error
>
>     Suhrid,
>       Type15 rewinds the data file as soon as it gets to the end so it
>     /shouldn't/ get an "end of file" error unless the file is blank.
>     I'm guessing it might be best to send your project to your
>     distributor's hotline though since it sounds as though you are
>     getting an end of file error when you shouldn't be.
>     regards,
>      David
>
>
>     On 06/09/2015 13:36, Suhrid A Deshmukh wrote:
>>     Thanks for the prompt response!
>>     What do you fix if the end of file is happening in type 15-2? It
>>     tries to read the weather files in the TMY2 format and some of
>>     them it reads fine and some of them it doesnt.
>>
>>     Regards,
>>     Suhrid
>>     ------------------------------------------------------------------------
>>     *From:* David BRADLEY [d.bradley at tess-inc.com
>>     <mailto:d.bradley at tess-inc.com>]
>>     *Sent:* Tuesday, June 09, 2015 1:22 PM
>>     *To:* TRNSYS users mailing list at OneBuilding.org; Suhrid A Deshmukh
>>     *Subject:* Re: [TRNSYS-users] end of file error
>>
>>     Suhrid,
>>      Check to make sure that the 10th parameter of Type51 sets the
>>     correct number of data points that are in your external file. The
>>     default value of the 10th parameter is 24. If your data file has
>>     less than 24 points in it then you'll need to modify the value of
>>     that parameter accordingly.
>>     regards,
>>      David
>>
>>
>>     On 6/8/2015 10:33 PM, Suhrid A Deshmukh wrote:
>>>     Hello all,
>>>     I am trying to simulate a cooling tower Type 51 with an external
>>>     file and the end of file is reached before the simulation ends.
>>>     Does anyone know the fix to this?
>>>
>>>     Regards,
>>>     Suhrid
>>>
>>>
>>>     _______________________________________________
>>>     TRNSYS-users mailing list
>>>     TRNSYS-users at lists.onebuilding.org  <mailto:TRNSYS-users at lists.onebuilding.org>
>>>     http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org
>>
>>     -- 
>>     ***************************
>>     David BRADLEY
>>     Principal
>>     Thermal Energy Systems Specialists, LLC
>>     22 North Carroll Street - suite 370
>>     Madison, WI  53703 USA
>>
>>     P:+1.608.274.2577  <tel:%2B1.608.274.2577>
>>     F:+1.608.278.1475  <tel:%2B1.608.278.1475>
>>     d.bradley at tess-inc.com  <mailto:d.bradley at tess-inc.com>
>>
>>     http://www.tess-inc.com
>>     http://www.trnsys.com
>
>     -- 
>     ***************************
>     David BRADLEY
>     Principal
>     Thermal Energy Systems Specialists, LLC
>     22 North Carroll Street - suite 370
>     Madison, WI  53703 USA
>
>     P:+1.608.274.2577  <tel:%2B1.608.274.2577>
>     F:+1.608.278.1475  <tel:%2B1.608.278.1475>
>     d.bradley at tess-inc.com  <mailto:d.bradley at tess-inc.com>
>
>     http://www.tess-inc.com
>     http://www.trnsys.com
>
>
>     _______________________________________________
>     TRNSYS-users mailing list
>     TRNSYS-users at lists.onebuilding.org
>     <mailto:TRNSYS-users at lists.onebuilding.org>
>     http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org
>
>
>
> _______________________________________________
> TRNSYS-users mailing list
> TRNSYS-users at lists.onebuilding.org
> http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org

-- 
***************************
David BRADLEY
Principal
Thermal Energy Systems Specialists, LLC
22 North Carroll Street - suite 370
Madison, WI  53703 USA

P:+1.608.274.2577
F:+1.608.278.1475
d.bradley at tess-inc.com

http://www.tess-inc.com
http://www.trnsys.com

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/trnsys-users-onebuilding.org/attachments/20150612/cfac58f5/attachment.htm>


More information about the TRNSYS-users mailing list