[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[EnergyPlus_Support] Re: Warning meassage in Exercise 2C of "Getting Started..."
There is another warning that the SEASONAL RESET SUPPLY AIR TEMP SCH is not used, when you turn on the Output Diagnostics for DisplayUnusedSchedules
ooi
--- In EnergyPlus_Support@xxxxxxxxxxxxxxx, Álvaro Fialho <alvarofialho@...> wrote:
>
> Hello all,
>
> I was playing a bit with the sample Exercises provided in the "Getting
> started with EnergyPlus" document. And Exercise 2C (the most "complete"
> one) outputs a warning message (and some consequent error messages) that
> I don't know what to do. As a "learning exercise", could you please help
> me into solving this? It is important to let you know that I'm a
> computer scientist, with no experience at all (for the moment) with the
> design of HVAC systems :-) Thanks!
>
>
> Here goes the warning message:
>
> ** Warning ** Coil:Cooling:DX:SingleSpeed "NORTH ZONE UNITARY
> COOLING COIL" - Full load outlet air dry-bulb temperature < 2C. This
> indicates the possibility of coil frost/freeze. Outlet temperature = 1.29 C.
> ** ~~~ ** ...Occurrence info = Chicago Ohare Intl Ap IL USA
> TMY3 WMO#=725300, 04/25 14:00 - 14:15
> ** ~~~ ** ... Possible reasons for low outlet air dry-bulb
> temperatures are: This DX coil
> ** ~~~ ** 1) may have a low inlet air dry-bulb temperature.
> Inlet air temperature = 21.146 C.
> ** ~~~ ** 2) may have a low air flow rate per watt of cooling
> capacity. Check inputs.
> ** ~~~ ** 3) is used as part of a HX assisted cooling coil
> which uses a high sensible effectiveness. Check inputs.
>
>
>
> And the consequent error message:
>
> ************* ===== Recurring Error Summary =====
> ************* The following recurring error messages occurred.
> *************
> ************* ** Warning ** Coil:Cooling:DX:SingleSpeed "NORTH ZONE
> UNITARY COOLING COIL" - Full load outlet temperature indicates a
> possibility of frost/freeze error continues. Outlet air temperature
> statistics follow:
> ************* ** ~~~ ** This error occurred 46 total times;
> ************* ** ~~~ ** during Warmup 0 times;
> ************* ** ~~~ ** during Sizing 0 times.
> ************* ** ~~~ ** Max=1.986818 Min=0.362192
>
>
> Thanks lot!
> Álvaro.
>
> ps: I'm sending the IDF attached, although you might all have it in the
> Examples/BasicsFiles folder of your E+ installation.
>
> !-Generator IDFEditor 1.29a
> !-Option OriginalOrderTop UseSpecialFormat
> !-NOTE: All comments with '!-' are ignored by the IDFEditor and are generated automatically.
> !- Use '!' comments if they need to be retained when using the IDFEditor.
>
> Output:Variable,*,Zone/Sys Air Temperature,Monthly,Office Occupancy 2;
>
> Output:Table:Monthly,
> Zone Temperature Report, !- Name
> 2, !- Digits After Decimal
> Zone Mean Air Temperature, !- Variable or Meter 1 Name
> SumOrAverage, !- Aggregation Type for Variable or Meter 1
> Zone Mean Air Temperature, !- Variable or Meter 2 Name
> Maximum, !- Aggregation Type for Variable or Meter 2
> Zone Mean Air Temperature, !- Variable or Meter 3 Name
> Minimum, !- Aggregation Type for Variable or Meter 3
> Zone People Number of Occupants, !- Variable or Meter 4 Name
> HoursPositive, !- Aggregation Type for Variable or Meter 4
> Zone Mean Air Temperature, !- Variable or Meter 5 Name
> SumOrAverageDuringHoursShown, !- Aggregation Type for Variable or Meter 5
> Zone Mean Air Temperature, !- Variable or Meter 6 Name
> MaximumDuringHoursShown, !- Aggregation Type for Variable or Meter 6
> Zone Mean Air Temperature, !- Variable or Meter 7 Name
> MinimumDuringHoursShown; !- Aggregation Type for Variable or Meter 7
>
> HVACTemplate:System:VAV,
> VAV with Reheat, !- Name
> Office HVAC, !- System Availability Schedule Name
> autosize, !- Supply Fan Maximum Flow Rate {m3/s}
> autosize, !- Supply Fan Minimum Flow Rate {m3/s}
> 0.7, !- Supply Fan Total Efficiency
> 1000, !- Supply Fan Delta Pressure {Pa}
> 0.9, !- Supply Fan Motor Efficiency
> 1, !- Supply Fan Motor in Air Stream Fraction
> ChilledWater, !- Cooling Coil Type
> , !- Cooling Coil Availability Schedule Name
> , !- Cooling Coil Setpoint Schedule Name
> 13, !- Cooling Coil Design Setpoint {C}
> None, !- Heating Coil Type
> , !- Heating Coil Availability Schedule Name
> , !- Heating Coil Setpoint Schedule Name
> 10.0, !- Heating Coil Design Setpoint {C}
> 0.8, !- Gas Heating Coil Efficiency
> , !- Gas Heating Coil Parasitic Electric Load {W}
> None, !- Preheat Coil Type
> , !- Preheat Coil Availability Schedule Name
> , !- Preheat Coil Setpoint Schedule Name
> 7.2, !- Preheat Coil Design Setpoint {C}
> 0.8, !- Gas Preheat Coil Efficiency
> , !- Gas Preheat Coil Parasitic Electric Load {W}
> autosize, !- Maximum Outdoor Air Flow Rate {m3/s}
> autosize, !- Minimum Outdoor Air Flow Rate {m3/s}
> ProportionalMinimum, !- Minimum Outdoor Air Control Type
> Office Minimum OA, !- Minimum Outdoor Air Schedule Name
> FixedDryBulb, !- Economizer Type
> NoLockout, !- Economizer Lockout
> , !- Economizer Upper Temperature Limit {C}
> , !- Economizer Lower Temperature Limit {C}
> , !- Economizer Upper Enthalpy Limit {J/kg}
> , !- Supply Plenum Name
> PLENUM, !- Return Plenum Name
> DrawThrough, !- Supply Fan Placement
> InletVaneDampers, !- Supply Fan Part-Load Power Coefficients
> StayOff, !- Night Cycle Control
> , !- Night Cycle Control Zone Name
> None, !- Heat Recovery Type
> 0.7, !- Sensible Heat Recovery Effectiveness
> 0.65, !- Latent Heat Recovery Effectiveness
> None, !- Cooling Coil Setpoint Reset Type
> None, !- Heating Coil Setpoint Reset Type
> , !- Dehumidification Control Type
> , !- Dehumidification Control Zone Name
> , !- Dehumidification Setpoint {percent}
> , !- Humidifier Type
> , !- Humidifier Availability Schedule Name
> , !- Humidifier Rated Capacity {m3/s}
> , !- Humidifier Rated Electric Power {W}
> , !- Humidifier Control Zone Name
> ; !- Humidifier Setpoint {percent}
>
> HVACTemplate:Zone:VAV,
> SOUTH PERIMETER, !- Zone Name
> VAV with Reheat, !- Template VAV System Name
> Office Thermostat, !- Template Thermostat Name
> autosize, !- Supply Air Maximum Flow Rate {m3/s}
> , !- Zone Heating Sizing Factor
> , !- Zone Cooling Sizing Factor
> Constant, !- Zone Minimum Air Flow Input Method
> 0.2, !- Constant Minimum Air Flow Fraction
> , !- Fixed Minimum Air Flow Rate {m3/s}
> , !- Minimum Air Flow Fraction Schedule Name
> Flow/Person, !- Outdoor Air Method
> 0.00944, !- Outdoor Air Flow Rate per Person {m3/s}
> 0.0, !- Outdoor Air Flow Rate per Zone Floor Area {m3/s-m2}
> 0.0, !- Outdoor Air Flow Rate per Zone {m3/s}
> HotWater, !- Reheat Coil Type
> , !- Reheat Coil Availability Schedule Name
> Reverse, !- Damper Heating Action
> , !- Maximum Flow per Zone Floor Area During Reheat {m3/s-m2}
> , !- Maximum Flow Fraction During Reheat
> , !- Maximum Reheat Air Temperature {C}
> , !- Design Specification Outdoor Air Object Name
> , !- Supply Plenum Name
> , !- Return Plenum Name
> None, !- Baseboard Heating Type
> , !- Baseboard Heating Availability Schedule Name
> autosize; !- Baseboard Heating Capacity {W}
>
> HVACTemplate:Zone:VAV,
> EAST PERIMETER, !- Zone Name
> VAV with Reheat, !- Template VAV System Name
> Office Thermostat, !- Template Thermostat Name
> autosize, !- Supply Air Maximum Flow Rate {m3/s}
> , !- Zone Heating Sizing Factor
> , !- Zone Cooling Sizing Factor
> Constant, !- Zone Minimum Air Flow Input Method
> 0.2, !- Constant Minimum Air Flow Fraction
> , !- Fixed Minimum Air Flow Rate {m3/s}
> , !- Minimum Air Flow Fraction Schedule Name
> Flow/Person, !- Outdoor Air Method
> 0.00944, !- Outdoor Air Flow Rate per Person {m3/s}
> 0.0, !- Outdoor Air Flow Rate per Zone Floor Area {m3/s-m2}
> 0.0, !- Outdoor Air Flow Rate per Zone {m3/s}
> HotWater, !- Reheat Coil Type
> , !- Reheat Coil Availability Schedule Name
> Reverse, !- Damper Heating Action
> , !- Maximum Flow per Zone Floor Area During Reheat {m3/s-m2}
> , !- Maximum Flow Fraction During Reheat
> , !- Maximum Reheat Air Temperature {C}
> , !- Design Specification Outdoor Air Object Name
> , !- Supply Plenum Name
> , !- Return Plenum Name
> None, !- Baseboard Heating Type
> , !- Baseboard Heating Availability Schedule Name
> autosize; !- Baseboard Heating Capacity {W}
>
> HVACTemplate:Zone:VAV,
> WEST PERIMETER, !- Zone Name
> VAV with Reheat, !- Template VAV System Name
> Office Thermostat, !- Template Thermostat Name
> autosize, !- Supply Air Maximum Flow Rate {m3/s}
> , !- Zone Heating Sizing Factor
> , !- Zone Cooling Sizing Factor
> Constant, !- Zone Minimum Air Flow Input Method
> 0.2, !- Constant Minimum Air Flow Fraction
> , !- Fixed Minimum Air Flow Rate {m3/s}
> , !- Minimum Air Flow Fraction Schedule Name
> Flow/Person, !- Outdoor Air Method
> 0.00944, !- Outdoor Air Flow Rate per Person {m3/s}
> 0.0, !- Outdoor Air Flow Rate per Zone Floor Area {m3/s-m2}
> 0.0, !- Outdoor Air Flow Rate per Zone {m3/s}
> HotWater, !- Reheat Coil Type
> , !- Reheat Coil Availability Schedule Name
> Reverse, !- Damper Heating Action
> , !- Maximum Flow per Zone Floor Area During Reheat {m3/s-m2}
> , !- Maximum Flow Fraction During Reheat
> , !- Maximum Reheat Air Temperature {C}
> , !- Design Specification Outdoor Air Object Name
> , !- Supply Plenum Name
> , !- Return Plenum Name
> None, !- Baseboard Heating Type
> , !- Baseboard Heating Availability Schedule Name
> autosize; !- Baseboard Heating Capacity {W}
>
> HVACTemplate:Zone:VAV,
> CORE, !- Zone Name
> VAV with Reheat, !- Template VAV System Name
> Office Thermostat, !- Template Thermostat Name
> autosize, !- Supply Air Maximum Flow Rate {m3/s}
> , !- Zone Heating Sizing Factor
> , !- Zone Cooling Sizing Factor
> Constant, !- Zone Minimum Air Flow Input Method
> 0.2, !- Constant Minimum Air Flow Fraction
> , !- Fixed Minimum Air Flow Rate {m3/s}
> , !- Minimum Air Flow Fraction Schedule Name
> Flow/Person, !- Outdoor Air Method
> 0.00944, !- Outdoor Air Flow Rate per Person {m3/s}
> 0.0, !- Outdoor Air Flow Rate per Zone Floor Area {m3/s-m2}
> 0.0, !- Outdoor Air Flow Rate per Zone {m3/s}
> HotWater, !- Reheat Coil Type
> , !- Reheat Coil Availability Schedule Name
> Reverse, !- Damper Heating Action
> , !- Maximum Flow per Zone Floor Area During Reheat {m3/s-m2}
> , !- Maximum Flow Fraction During Reheat
> , !- Maximum Reheat Air Temperature {C}
> , !- Design Specification Outdoor Air Object Name
> , !- Supply Plenum Name
> , !- Return Plenum Name
> None, !- Baseboard Heating Type
> , !- Baseboard Heating Availability Schedule Name
> autosize; !- Baseboard Heating Capacity {W}
>
> HVACTemplate:Plant:ChilledWaterLoop,
> Chilled Water Plant, !- Name
> , !- Pump Schedule Name
> Intermittent, !- Pump Control Type
> Default, !- Chiller Plant Operation Scheme Type
> , !- Chiller Plant Equipment Operation Schemes Name
> , !- Chilled Water Setpoint Schedule Name
> 7.22, !- Chilled Water Design Setpoint {C}
> ConstantPrimaryNoSecondary, !- Chilled Water Pump Configuration
> 179352, !- Primary Chilled Water Pump Rated Head {Pa}
> 179352, !- Secondary Chilled Water Pump Rated Head {Pa}
> Default, !- Condenser Plant Operation Scheme Type
> , !- Condenser Equipment Operation Schemes Name
> SpecifiedSetpoint, !- Condenser Water Temperature Control Type
> , !- Condenser Water Setpoint Schedule Name
> 29.4, !- Condenser Water Design Setpoint {C}
> 179352, !- Condenser Water Pump Rated Head {Pa}
> None, !- Chilled Water Setpoint Reset Type
> 12.2, !- Chilled Water Setpoint at Outdoor Dry-Bulb Low {C}
> 15.6, !- Chilled Water Reset Outdoor Dry-Bulb Low {C}
> 6.7, !- Chilled Water Setpoint at Outdoor Dry-Bulb High {C}
> 26.7; !- Chilled Water Reset Outdoor Dry-Bulb High {C}
>
> HVACTemplate:Plant:Chiller,
> Chiller 1, !- Name
> ElectricReciprocatingChiller, !- Chiller Type
> autosize, !- Capacity {W}
> 3.6, !- Nominal COP {W/W}
> WaterCooled, !- Condenser Type
> , !- Priority
> 1.0; !- Sizing Factor
>
> HVACTemplate:Plant:Tower,
> Tower 1, !- Name
> TwoSpeed, !- Tower Type
> autosize, !- High Speed Nominal Capacity {W}
> autosize, !- High Speed Fan Power {W}
> autosize, !- Low Speed Nominal Capacity {W}
> autosize, !- Low Speed Fan Power {W}
> autosize, !- Free Convection Capacity {W}
> , !- Priority
> 1.0; !- Sizing Factor
>
> HVACTemplate:Plant:HotWaterLoop,
> Hot Water Plant, !- Name
> , !- Pump Schedule Name
> Intermittent, !- Pump Control Type
> Default, !- Hot Water Plant Operation Scheme Type
> , !- Hot Water Plant Equipment Operation Schemes Name
> , !- Hot Water Setpoint Schedule Name
> 82, !- Hot Water Design Setpoint {C}
> ConstantFlow, !- Hot Water Pump Configuration
> 179352, !- Hot Water Pump Rated Head {Pa}
> None, !- Hot Water Setpoint Reset Type
> 82.2, !- Hot Water Setpoint at Outdoor Dry-Bulb Low {C}
> -6.7, !- Hot Water Reset Outdoor Dry-Bulb Low {C}
> 65.6, !- Hot Water Setpoint at Outdoor Dry-Bulb High {C}
> 10; !- Hot Water Reset Outdoor Dry-Bulb High {C}
>
> HVACTemplate:Plant:Boiler,
> Boiler 1, !- Name
> HotWaterBoiler, !- Boiler Type
> autosize, !- Capacity {W}
> 0.8, !- Efficiency
> NaturalGas, !- Fuel Type
> , !- Priority
> 1.0; !- Sizing Factor
>
> Output:Variable,*,VAV Terminal Damper Position,Monthly;
>
> Output:Variable,*,Chiller Evap Heat Trans Rate,Monthly;
>
> Output:Variable,*,Chiller COP,Monthly;
>
> Output:Variable,*,Boiler Heating Output Rate,Monthly;
>
> Output:Variable,*,Tower Heat Transfer,Monthly;
>
> Output:Variable,*,Furnace Fan Part-Load Ratio,Monthly;
>
> Output:Variable,*,DX Cooling Coil Runtime Fraction,Monthly;
>
> Output:Variable,*,Heating Coil Runtime Fraction,Monthly;
>
> HVACTemplate:System:Unitary,
> North Zone Unitary, !- Name
> Office HVAC, !- System Availability Schedule Name
> NORTH PERIMETER, !- Control Zone or Thermostat Location Name
> autosize, !- Supply Fan Maximum Flow Rate {m3/s}
> Continuous, !- Supply Fan Operating Mode Schedule Name
> 0.7, !- Supply Fan Total Efficiency
> 600, !- Supply Fan Delta Pressure {Pa}
> 0.9, !- Supply Fan Motor Efficiency
> 1, !- Supply Fan Motor in Air Stream Fraction
> SingleSpeedDX, !- Cooling Coil Type
> , !- Cooling Coil Availability Schedule Name
> autosize, !- Cooling Coil Capacity {W}
> autosize, !- Cooling Coil Rated Sensible Heat Ratio
> 3, !- Cooling Coil Rated COP
> Gas, !- Heating Coil Type
> , !- Heating Coil Availability Schedule Name
> autosize, !- Heating Coil Capacity {W}
> 0.8, !- Gas Heating Coil Efficiency
> , !- Gas Heating Coil Parasitic Electric Load {W}
> autosize, !- Maximum Outdoor Air Flow Rate {m3/s}
> autosize, !- Minimum Outdoor Air Flow Rate {m3/s}
> Office Minimum OA, !- Minimum Outdoor Air Schedule Name
> NoEconomizer, !- Economizer Type
> NoLockout, !- Economizer Lockout
> , !- Economizer Upper Temperature Limit {C}
> , !- Economizer Lower Temperature Limit {C}
> , !- Economizer Upper Enthalpy Limit {J/kg}
> , !- Supply Plenum Name
> , !- Return Plenum Name
> BlowThrough, !- Supply Fan Placement
> StayOff, !- Night Cycle Control
> , !- Night Cycle Control Zone Name
> None, !- Heat Recovery Type
> 0.7, !- Sensible Heat Recovery Effectiveness
> 0.65, !- Latent Heat Recovery Effectiveness
> , !- Dehumidification Control Type
> , !- Dehumidification Control Zone Name
> , !- Dehumidification Setpoint {percent}
> , !- Humidifier Type
> , !- Humidifier Availability Schedule Name
> , !- Humidifier Rated Capacity {m3/s}
> , !- Humidifier Rated Electric Power {W}
> , !- Humidifier Control Zone Name
> ; !- Humidifier Setpoint {percent}
>
> Sizing:Parameters,
> 1.2, !- Heating Sizing Factor
> 1.2; !- Cooling Sizing Factor
>
> HVACTemplate:Thermostat,
> Office Thermostat, !- Name
> Office Heating Setpoints,!- Heating Setpoint Schedule Name
> , !- Constant Heating Setpoint {C}
> Office Cooling Setpoints,!- Cooling Setpoint Schedule Name
> ; !- Constant Cooling Setpoint {C}
>
> HVACTemplate:Zone:Unitary,
> NORTH PERIMETER, !- Zone Name
> North Zone Unitary, !- Template Unitary System Name
> Office Thermostat, !- Template Thermostat Name
> autosize, !- Supply Air Maximum Flow Rate {m3/s}
> , !- Zone Heating Sizing Factor
> , !- Zone Cooling Sizing Factor
> Flow/Person, !- Outdoor Air Method
> 0.00944, !- Outdoor Air Flow Rate per Person {m3/s}
> 0.0, !- Outdoor Air Flow Rate per Zone Floor Area {m3/s-m2}
> 0.0, !- Outdoor Air Flow Rate per Zone {m3/s}
> , !- Supply Plenum Name
> , !- Return Plenum Name
> None, !- Baseboard Heating Type
> , !- Baseboard Heating Availability Schedule Name
> autosize; !- Baseboard Heating Capacity {W}
>
> ! Introduction to EnergyPlus - Exercise 2C
> !
> ! Building: Single floor rectangular building 30.5 m (100 ft) x 15.2 m (50 ft). 5 zones -
> ! 4 exterior, 1 interior, zone height 2.4 m (8 ft). Exterior zone
> ! depth is 3.7 m (12 ft). There is a 0.6 m (2 ft) high return plenum. The
> ! overall building height is 3m (10 ft). There are windows on
> ! all 4 facades; the south and north facades have glass doors.
> ! The south facing glass is shaded by overhangs. The walls
> ! are woodshingle over plywood, R11 insulation, and gypboard.
> ! The roof is a gravel built up roof with mineral board
> ! insulation and plywood sheathing. The floor slab is 0.1 m (4 in)
> ! of heavy concrete. The windows and glass doors are double
> ! pane Low-e clear glass with argon gap. The window to wall ratio is
> ! approximately 0.3.
> !
> ! The building is oriented with the long axis running east-west.
> !
> ! Floor Area: 463.6 m2 (5000 ft2)
> !
> ! Internal: Lighting is 16 W/m2 (1.5 W/ft2), office equip is 10.8 W/m2 (1.0 W/ft2).
> ! 1 occupant per 9.3 m2 (100 ft2) of floor area. The
> ! Infiltration is 0.25 air changes per hour.
> !
> ! HVAC: Single-zone unitary with DX cooling and gas heating serving NORTH PERIMETER zone.
> ! VAV with hot water reheat, return plenum, chiller, boiler, and tower serving
> ! the other four occupied zones.
> !
> ! Environment: Chicago, IL, USA, TMY2
> !
> !
>
> VERSION,6.0;
>
> Building,
> Exercise 2C, !- Name
> 0.0, !- North Axis {deg}
> City, !- Terrain
> 0.04, !- Loads Convergence Tolerance Value
> 0.4, !- Temperature Convergence Tolerance Value {deltaC}
> FullInteriorAndExterior, !- Solar Distribution
> ; !- Maximum Number of Warmup Days
>
> Timestep,4;
>
> SurfaceConvectionAlgorithm:Inside,Simple;
>
> SurfaceConvectionAlgorithm:Outside,SimpleCombined;
>
> HeatBalanceAlgorithm,ConductionTransferFunction;
>
> ZoneCapacitanceMultiplier:ResearchSpecial,
> 1, !- Temperature Capacity Multiplier
> 1, !- Humidity Capacity Multiplier
> 1; !- Carbon Dioxide Capacity Multiplier
>
> SimulationControl,
> Yes, !- Do Zone Sizing Calculation
> Yes, !- Do System Sizing Calculation
> Yes, !- Do Plant Sizing Calculation
> No, !- Run Simulation for Sizing Periods
> Yes; !- Run Simulation for Weather File Run Periods
>
> RunPeriod,
> , !- Name
> 1, !- Begin Month
> 1, !- Begin Day of Month
> 12, !- End Month
> 31, !- End Day of Month
> UseWeatherFile, !- Day of Week for Start Day
> Yes, !- Use Weather File Holidays and Special Days
> Yes, !- Use Weather File Daylight Saving Period
> No, !- Apply Weekend Holiday Rule
> Yes, !- Use Weather File Rain Indicators
> Yes, !- Use Weather File Snow Indicators
> 1; !- Number of Times Runperiod to be Repeated
>
> Site:Location,
> CHICAGO_IL_USA TMY2-94846, !- Name
> 41.78, !- Latitude {deg}
> -87.75, !- Longitude {deg}
> -6.00, !- Time Zone {hr}
> 190.00; !- Elevation {m}
>
> ! CHICAGO_IL_USA Heating 99%, MaxDB= -18.10°C
>
> SizingPeriod:DesignDay,
> CHICAGO_IL_USA Heating 99% Conditions, !- Name
> -18.10, !- Maximum Dry-Bulb Temperature {C}
> 0.00, !- Daily Temperature Range {deltaC}
> -18.10, !- Humidity Indicating Conditions at Maximum Dry-Bulb
> 99063., !- Barometric Pressure {Pa}
> 4.60, !- Wind Speed {m/s}
> 270.00, !- Wind Direction {deg}
> 0.00, !- Sky Clearness
> 0, !- Rain Indicator
> 0, !- Snow Indicator
> 21, !- Day of Month
> 1, !- Month
> WinterDesignDay, !- Day Type
> 0, !- Daylight Saving Time Indicator
> WetBulb; !- Humidity Indicating Type
>
> ! CHICAGO_IL_USA Cooling (DB=>MWB) 1%, MaxDB= 31.30°C MWB= 22.80°C
>
> SizingPeriod:DesignDay,
> CHICAGO_IL_USA Cooling 1% Conditions DB=>MWB, !- Name
> 31.30, !- Maximum Dry-Bulb Temperature {C}
> 10.90, !- Daily Temperature Range {deltaC}
> 22.80, !- Humidity Indicating Conditions at Maximum Dry-Bulb
> 99063., !- Barometric Pressure {Pa}
> 5.40, !- Wind Speed {m/s}
> 230.00, !- Wind Direction {deg}
> 1.00, !- Sky Clearness
> 0, !- Rain Indicator
> 0, !- Snow Indicator
> 21, !- Day of Month
> 7, !- Month
> SummerDesignDay, !- Day Type
> 0, !- Daylight Saving Time Indicator
> WetBulb; !- Humidity Indicating Type
>
> Site:GroundTemperature:BuildingSurface,20.4,20.4,20.4,20.4,21.5,22.7,22.9,23.0,23.0,21.9,20.7,20.5;
>
> Material,
> WD10, !- Name
> MediumSmooth, !- Roughness
> 0.667, !- Thickness {m}
> 0.115, !- Conductivity {W/m-K}
> 513, !- Density {kg/m3}
> 1381, !- Specific Heat {J/kg-K}
> 0.9, !- Thermal Absorptance
> 0.78, !- Solar Absorptance
> 0.78; !- Visible Absorptance
>
> Material,
> RG01, !- Name
> Rough, !- Roughness
> 1.2700000E-02, !- Thickness {m}
> 1.442000, !- Conductivity {W/m-K}
> 881.0000, !- Density {kg/m3}
> 1674.000, !- Specific Heat {J/kg-K}
> 0.9000000, !- Thermal Absorptance
> 0.6500000, !- Solar Absorptance
> 0.6500000; !- Visible Absorptance
>
> Material,
> BR01, !- Name
> VeryRough, !- Roughness
> 9.4999997E-03, !- Thickness {m}
> 0.1620000, !- Conductivity {W/m-K}
> 1121.000, !- Density {kg/m3}
> 1464.000, !- Specific Heat {J/kg-K}
> 0.9000000, !- Thermal Absorptance
> 0.7000000, !- Solar Absorptance
> 0.7000000; !- Visible Absorptance
>
> Material,
> IN46, !- Name
> VeryRough, !- Roughness
> 7.6200001E-02, !- Thickness {m}
> 2.3000000E-02, !- Conductivity {W/m-K}
> 24.00000, !- Density {kg/m3}
> 1590.000, !- Specific Heat {J/kg-K}
> 0.9000000, !- Thermal Absorptance
> 0.5000000, !- Solar Absorptance
> 0.5000000; !- Visible Absorptance
>
> Material,
> WD01, !- Name
> MediumSmooth, !- Roughness
> 1.9099999E-02, !- Thickness {m}
> 0.1150000, !- Conductivity {W/m-K}
> 513.0000, !- Density {kg/m3}
> 1381.000, !- Specific Heat {J/kg-K}
> 0.9000000, !- Thermal Absorptance
> 0.7800000, !- Solar Absorptance
> 0.7800000; !- Visible Absorptance
>
> Material,
> PW03, !- Name
> MediumSmooth, !- Roughness
> 1.2700000E-02, !- Thickness {m}
> 0.1150000, !- Conductivity {W/m-K}
> 545.0000, !- Density {kg/m3}
> 1213.000, !- Specific Heat {J/kg-K}
> 0.9000000, !- Thermal Absorptance
> 0.7800000, !- Solar Absorptance
> 0.7800000; !- Visible Absorptance
>
> Material,
> IN02, !- Name
> Rough, !- Roughness
> 9.0099998E-02, !- Thickness {m}
> 4.3000001E-02, !- Conductivity {W/m-K}
> 10.00000, !- Density {kg/m3}
> 837.0000, !- Specific Heat {J/kg-K}
> 0.9000000, !- Thermal Absorptance
> 0.7500000, !- Solar Absorptance
> 0.7500000; !- Visible Absorptance
>
> Material,
> GP01, !- Name
> MediumSmooth, !- Roughness
> 1.2700000E-02, !- Thickness {m}
> 0.1600000, !- Conductivity {W/m-K}
> 801.0000, !- Density {kg/m3}
> 837.0000, !- Specific Heat {J/kg-K}
> 0.9000000, !- Thermal Absorptance
> 0.7500000, !- Solar Absorptance
> 0.7500000; !- Visible Absorptance
>
> Material,
> GP02, !- Name
> MediumSmooth, !- Roughness
> 1.5900001E-02, !- Thickness {m}
> 0.1600000, !- Conductivity {W/m-K}
> 801.0000, !- Density {kg/m3}
> 837.0000, !- Specific Heat {J/kg-K}
> 0.9000000, !- Thermal Absorptance
> 0.7500000, !- Solar Absorptance
> 0.7500000; !- Visible Absorptance
>
> Material,
> CC03, !- Name
> MediumRough, !- Roughness
> 0.1016000, !- Thickness {m}
> 1.310000, !- Conductivity {W/m-K}
> 2243.000, !- Density {kg/m3}
> 837.0000, !- Specific Heat {J/kg-K}
> 0.9000000, !- Thermal Absorptance
> 0.6500000, !- Solar Absorptance
> 0.6500000; !- Visible Absorptance
>
> Material:NoMass,
> CP01, !- Name
> Rough, !- Roughness
> 0.3670000, !- Thermal Resistance {m2-K/W}
> 0.9000000, !- Thermal Absorptance
> 0.7500000, !- Solar Absorptance
> 0.7500000; !- Visible Absorptance
>
> Material:NoMass,
> MAT-SB-U, !- Name
> Rough, !- Roughness
> 0.117406666, !- Thermal Resistance {m2-K/W}
> 0.65, !- Thermal Absorptance
> 0.65, !- Solar Absorptance
> 0.65; !- Visible Absorptance
>
> Material:NoMass,
> MAT-CLNG-1, !- Name
> Rough, !- Roughness
> 0.652259290, !- Thermal Resistance {m2-K/W}
> 0.65, !- Thermal Absorptance
> 0.65, !- Solar Absorptance
> 0.65; !- Visible Absorptance
>
> Material:NoMass,
> MAT-FLOOR-1, !- Name
> Rough, !- Roughness
> 3.522199631, !- Thermal Resistance {m2-K/W}
> 0.65, !- Thermal Absorptance
> 0.65, !- Solar Absorptance
> 0.65; !- Visible Absorptance
>
> Material:AirGap,
> AL21, !- Name
> 0.1570000; !- Thermal Resistance {m2-K/W}
>
> Material:AirGap,
> AL23, !- Name
> 0.1530000; !- Thermal Resistance {m2-K/W}
>
> WindowMaterial:Glazing,
> CLEAR 3MM, !- Name
> SpectralAverage, !- Optical Data Type
> , !- Window Glass Spectral Data Set Name
> 0.003, !- Thickness {m}
> 0.837, !- Solar Transmittance at Normal Incidence
> 0.075, !- Front Side Solar Reflectance at Normal Incidence
> 0.075, !- Back Side Solar Reflectance at Normal Incidence
> 0.898, !- Visible Transmittance at Normal Incidence
> 0.081, !- Front Side Visible Reflectance at Normal Incidence
> 0.081, !- Back Side Visible Reflectance at Normal Incidence
> 0.0, !- Infrared Transmittance at Normal Incidence
> 0.84, !- Front Side Infrared Hemispherical Emissivity
> 0.84, !- Back Side Infrared Hemispherical Emissivity
> 0.9; !- Conductivity {W/m-K}
>
> WindowMaterial:Glazing,
> GREY 3MM, !- Name
> SpectralAverage, !- Optical Data Type
> , !- Window Glass Spectral Data Set Name
> 0.003, !- Thickness {m}
> 0.626, !- Solar Transmittance at Normal Incidence
> 0.061, !- Front Side Solar Reflectance at Normal Incidence
> 0.061, !- Back Side Solar Reflectance at Normal Incidence
> 0.611, !- Visible Transmittance at Normal Incidence
> 0.061, !- Front Side Visible Reflectance at Normal Incidence
> 0.061, !- Back Side Visible Reflectance at Normal Incidence
> 0.0, !- Infrared Transmittance at Normal Incidence
> 0.84, !- Front Side Infrared Hemispherical Emissivity
> 0.84, !- Back Side Infrared Hemispherical Emissivity
> 0.9; !- Conductivity {W/m-K}
>
> WindowMaterial:Glazing,
> CLEAR 6MM, !- Name
> SpectralAverage, !- Optical Data Type
> , !- Window Glass Spectral Data Set Name
> 0.006, !- Thickness {m}
> 0.775, !- Solar Transmittance at Normal Incidence
> 0.071, !- Front Side Solar Reflectance at Normal Incidence
> 0.071, !- Back Side Solar Reflectance at Normal Incidence
> 0.881, !- Visible Transmittance at Normal Incidence
> 0.080, !- Front Side Visible Reflectance at Normal Incidence
> 0.080, !- Back Side Visible Reflectance at Normal Incidence
> 0.0, !- Infrared Transmittance at Normal Incidence
> 0.84, !- Front Side Infrared Hemispherical Emissivity
> 0.84, !- Back Side Infrared Hemispherical Emissivity
> 0.9; !- Conductivity {W/m-K}
>
> WindowMaterial:Glazing,
> LoE CLEAR 6MM, !- Name
> SpectralAverage, !- Optical Data Type
> , !- Window Glass Spectral Data Set Name
> 0.006, !- Thickness {m}
> 0.600, !- Solar Transmittance at Normal Incidence
> 0.170, !- Front Side Solar Reflectance at Normal Incidence
> 0.220, !- Back Side Solar Reflectance at Normal Incidence
> 0.840, !- Visible Transmittance at Normal Incidence
> 0.055, !- Front Side Visible Reflectance at Normal Incidence
> 0.078, !- Back Side Visible Reflectance at Normal Incidence
> 0.0, !- Infrared Transmittance at Normal Incidence
> 0.84, !- Front Side Infrared Hemispherical Emissivity
> 0.10, !- Back Side Infrared Hemispherical Emissivity
> 0.9; !- Conductivity {W/m-K}
>
> WindowMaterial:Gas,
> AIR 6MM, !- Name
> Air, !- Gas Type
> 0.0063; !- Thickness {m}
>
> WindowMaterial:Gas,
> AIR 13MM, !- Name
> Air, !- Gas Type
> 0.0127; !- Thickness {m}
>
> WindowMaterial:Gas,
> ARGON 13MM, !- Name
> Argon, !- Gas Type
> 0.0127; !- Thickness {m}
>
> Construction,
> ROOF-1, !- Name
> RG01, !- Outside Layer
> BR01, !- Layer 2
> IN46, !- Layer 3
> WD01; !- Layer 4
>
> Construction,
> WALL-1, !- Name
> WD01, !- Outside Layer
> PW03, !- Layer 2
> IN02, !- Layer 3
> GP01; !- Layer 4
>
> Construction,
> CLNG-1, !- Name
> MAT-CLNG-1; !- Outside Layer
>
> Construction,
> SB-U, !- Name
> MAT-SB-U; !- Outside Layer
>
> Construction,
> FLOOR-1, !- Name
> MAT-FLOOR-1; !- Outside Layer
>
> Construction,
> FLOOR-SLAB-1, !- Name
> CC03; !- Outside Layer
>
> Construction,
> INT-WALL-1, !- Name
> GP02, !- Outside Layer
> AL21, !- Layer 2
> GP02; !- Layer 3
>
> Construction,
> Double LoE Clear Argon, !- Name
> LoE CLEAR 6MM, !- Outside Layer
> ARGON 13MM, !- Layer 2
> CLEAR 6MM; !- Layer 3
>
> Zone,
> PLENUM, !- Name
> 0, !- Direction of Relative North {deg}
> 0, !- X Origin {m}
> 0, !- Y Origin {m}
> 0, !- Z Origin {m}
> 1, !- Type
> 1, !- Multiplier
> 0.609600067, !- Ceiling Height {m}
> 283.2, !- Volume {m3}
> , !- Zone Inside Convection Algorithm
> , !- Zone Outside Convection Algorithm
> No; !- Part of Total Floor Area
>
> Zone,
> SOUTH PERIMETER, !- Name
> 0, !- Direction of Relative North {deg}
> 0, !- X Origin {m}
> 0, !- Y Origin {m}
> 0, !- Z Origin {m}
> 1, !- Type
> 1, !- Multiplier
> 2.438400269, !- Ceiling Height {m}
> 239.247360229, !- Volume {m3}
> , !- Zone Inside Convection Algorithm
> , !- Zone Outside Convection Algorithm
> Yes; !- Part of Total Floor Area
>
> Zone,
> EAST PERIMETER, !- Name
> 0, !- Direction of Relative North {deg}
> 0, !- X Origin {m}
> 0, !- Y Origin {m}
> 0, !- Z Origin {m}
> 1, !- Type
> 1, !- Multiplier
> 2.438400269, !- Ceiling Height {m}
> 103.311355591, !- Volume {m3}
> , !- Zone Inside Convection Algorithm
> , !- Zone Outside Convection Algorithm
> Yes; !- Part of Total Floor Area
>
> Zone,
> NORTH PERIMETER, !- Name
> 0, !- Direction of Relative North {deg}
> 0, !- X Origin {m}
> 0, !- Y Origin {m}
> 0, !- Z Origin {m}
> 1, !- Type
> 1, !- Multiplier
> 2.438400269, !- Ceiling Height {m}
> 239.247360229, !- Volume {m3}
> , !- Zone Inside Convection Algorithm
> , !- Zone Outside Convection Algorithm
> Yes; !- Part of Total Floor Area
>
> Zone,
> WEST PERIMETER, !- Name
> 0, !- Direction of Relative North {deg}
> 0, !- X Origin {m}
> 0, !- Y Origin {m}
> 0, !- Z Origin {m}
> 1, !- Type
> 1, !- Multiplier
> 2.438400269, !- Ceiling Height {m}
> 103.311355591, !- Volume {m3}
> , !- Zone Inside Convection Algorithm
> , !- Zone Outside Convection Algorithm
> Yes; !- Part of Total Floor Area
>
> Zone,
> CORE, !- Name
> 0, !- Direction of Relative North {deg}
> 0, !- X Origin {m}
> 0, !- Y Origin {m}
> 0, !- Z Origin {m}
> 1, !- Type
> 1, !- Multiplier
> 2.438400269, !- Ceiling Height {m}
> 447.682556152, !- Volume {m3}
> , !- Zone Inside Convection Algorithm
> , !- Zone Outside Convection Algorithm
> Yes; !- Part of Total Floor Area
>
> GlobalGeometryRules,
> UpperLeftCorner, !- Starting Vertex Position
> Counterclockwise, !- Vertex Entry Direction
> Relative; !- Coordinate System
>
> BuildingSurface:Detailed,
> WALL-1PF, !- Name
> Wall, !- Surface Type
> WALL-1, !- Construction Name
> PLENUM, !- Zone Name
> Outdoors, !- Outside Boundary Condition
> , !- Outside Boundary Condition Object
> SunExposed, !- Sun Exposure
> WindExposed, !- Wind Exposure
> 0.50000, !- View Factor to Ground
> 4, !- Number of Vertices
> 0.0,0.0,3.0, !- X,Y,Z ==> Vertex 1 {m}
> 0.0,0.0,2.4, !- X,Y,Z ==> Vertex 2 {m}
> 30.5,0.0,2.4, !- X,Y,Z ==> Vertex 3 {m}
> 30.5,0.0,3.0; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> WALL-1PR, !- Name
> Wall, !- Surface Type
> WALL-1, !- Construction Name
> PLENUM, !- Zone Name
> Outdoors, !- Outside Boundary Condition
> , !- Outside Boundary Condition Object
> SunExposed, !- Sun Exposure
> WindExposed, !- Wind Exposure
> 0.50000, !- View Factor to Ground
> 4, !- Number of Vertices
> 30.5,0.0,3.0, !- X,Y,Z ==> Vertex 1 {m}
> 30.5,0.0,2.4, !- X,Y,Z ==> Vertex 2 {m}
> 30.5,15.2,2.4, !- X,Y,Z ==> Vertex 3 {m}
> 30.5,15.2,3.0; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> WALL-1PB, !- Name
> Wall, !- Surface Type
> WALL-1, !- Construction Name
> PLENUM, !- Zone Name
> Outdoors, !- Outside Boundary Condition
> , !- Outside Boundary Condition Object
> SunExposed, !- Sun Exposure
> WindExposed, !- Wind Exposure
> 0.50000, !- View Factor to Ground
> 4, !- Number of Vertices
> 30.5,15.2,3.0, !- X,Y,Z ==> Vertex 1 {m}
> 30.5,15.2,2.4, !- X,Y,Z ==> Vertex 2 {m}
> 0.0,15.2,2.4, !- X,Y,Z ==> Vertex 3 {m}
> 0.0,15.2,3.0; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> WALL-1PL, !- Name
> Wall, !- Surface Type
> WALL-1, !- Construction Name
> PLENUM, !- Zone Name
> Outdoors, !- Outside Boundary Condition
> , !- Outside Boundary Condition Object
> SunExposed, !- Sun Exposure
> WindExposed, !- Wind Exposure
> 0.50000, !- View Factor to Ground
> 4, !- Number of Vertices
> 0.0,15.2,3.0, !- X,Y,Z ==> Vertex 1 {m}
> 0.0,15.2,2.4, !- X,Y,Z ==> Vertex 2 {m}
> 0.0,0.0,2.4, !- X,Y,Z ==> Vertex 3 {m}
> 0.0,0.0,3.0; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> TOP-1, !- Name
> Roof, !- Surface Type
> ROOF-1, !- Construction Name
> PLENUM, !- Zone Name
> Outdoors, !- Outside Boundary Condition
> , !- Outside Boundary Condition Object
> SunExposed, !- Sun Exposure
> WindExposed, !- Wind Exposure
> 0.00000, !- View Factor to Ground
> 4, !- Number of Vertices
> 0.0,15.2,3.0, !- X,Y,Z ==> Vertex 1 {m}
> 0.0,0.0,3.0, !- X,Y,Z ==> Vertex 2 {m}
> 30.5,0.0,3.0, !- X,Y,Z ==> Vertex 3 {m}
> 30.5,15.2,3.0; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> C1-1P, !- Name
> Floor, !- Surface Type
> CLNG-1, !- Construction Name
> PLENUM, !- Zone Name
> Surface, !- Outside Boundary Condition
> C1-1, !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 26.8,3.7,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 30.5,0.0,2.4, !- X,Y,Z ==> Vertex 2 {m}
> 0.0,0.0,2.4, !- X,Y,Z ==> Vertex 3 {m}
> 3.7,3.7,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> C2-1P, !- Name
> Floor, !- Surface Type
> CLNG-1, !- Construction Name
> PLENUM, !- Zone Name
> Surface, !- Outside Boundary Condition
> C2-1, !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 26.8,11.6,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 30.5,15.2,2.4, !- X,Y,Z ==> Vertex 2 {m}
> 30.5,0.0,2.4, !- X,Y,Z ==> Vertex 3 {m}
> 26.8,3.7,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> C3-1P, !- Name
> Floor, !- Surface Type
> CLNG-1, !- Construction Name
> PLENUM, !- Zone Name
> Surface, !- Outside Boundary Condition
> C3-1, !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 26.8,11.6,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 3.7,11.6,2.4, !- X,Y,Z ==> Vertex 2 {m}
> 0.0,15.2,2.4, !- X,Y,Z ==> Vertex 3 {m}
> 30.5,15.2,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> C4-1P, !- Name
> Floor, !- Surface Type
> CLNG-1, !- Construction Name
> PLENUM, !- Zone Name
> Surface, !- Outside Boundary Condition
> C4-1, !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 3.7,3.7,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 0.0,0.0,2.4, !- X,Y,Z ==> Vertex 2 {m}
> 0.0,15.2,2.4, !- X,Y,Z ==> Vertex 3 {m}
> 3.7,11.6,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> C5-1P, !- Name
> Floor, !- Surface Type
> CLNG-1, !- Construction Name
> PLENUM, !- Zone Name
> Surface, !- Outside Boundary Condition
> C5-1, !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 26.8,11.6,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 26.8,3.7,2.4, !- X,Y,Z ==> Vertex 2 {m}
> 3.7,3.7,2.4, !- X,Y,Z ==> Vertex 3 {m}
> 3.7,11.6,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> FRONT-1, !- Name
> Wall, !- Surface Type
> WALL-1, !- Construction Name
> SOUTH PERIMETER, !- Zone Name
> Outdoors, !- Outside Boundary Condition
> , !- Outside Boundary Condition Object
> SunExposed, !- Sun Exposure
> WindExposed, !- Wind Exposure
> 0.50000, !- View Factor to Ground
> 4, !- Number of Vertices
> 0.0,0.0,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 0.0,0.0,0.0, !- X,Y,Z ==> Vertex 2 {m}
> 30.5,0.0,0.0, !- X,Y,Z ==> Vertex 3 {m}
> 30.5,0.0,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> C1-1, !- Name
> Ceiling, !- Surface Type
> CLNG-1, !- Construction Name
> SOUTH PERIMETER, !- Zone Name
> Surface, !- Outside Boundary Condition
> C1-1P, !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 3.7,3.7,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 0.0,0.0,2.4, !- X,Y,Z ==> Vertex 2 {m}
> 30.5,0.0,2.4, !- X,Y,Z ==> Vertex 3 {m}
> 26.8,3.7,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> F1-1, !- Name
> Floor, !- Surface Type
> FLOOR-SLAB-1, !- Construction Name
> SOUTH PERIMETER, !- Zone Name
> Ground, !- Outside Boundary Condition
> , !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 26.8,3.7,0.0, !- X,Y,Z ==> Vertex 1 {m}
> 30.5,0.0,0.0, !- X,Y,Z ==> Vertex 2 {m}
> 0.0,0.0,0.0, !- X,Y,Z ==> Vertex 3 {m}
> 3.7,3.7,0.0; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> SB12, !- Name
> Wall, !- Surface Type
> INT-WALL-1, !- Construction Name
> SOUTH PERIMETER, !- Zone Name
> Surface, !- Outside Boundary Condition
> SB21, !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 30.5,0.0,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 30.5,0.0,0.0, !- X,Y,Z ==> Vertex 2 {m}
> 26.8,3.7,0.0, !- X,Y,Z ==> Vertex 3 {m}
> 26.8,3.7,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> SB14, !- Name
> Wall, !- Surface Type
> INT-WALL-1, !- Construction Name
> SOUTH PERIMETER, !- Zone Name
> Surface, !- Outside Boundary Condition
> SB41, !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 3.7,3.7,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 3.7,3.7,0.0, !- X,Y,Z ==> Vertex 2 {m}
> 0.0,0.0,0.0, !- X,Y,Z ==> Vertex 3 {m}
> 0.0,0.0,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> SB15, !- Name
> Wall, !- Surface Type
> INT-WALL-1, !- Construction Name
> SOUTH PERIMETER, !- Zone Name
> Surface, !- Outside Boundary Condition
> SB51, !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 26.8,3.7,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 26.8,3.7,0.0, !- X,Y,Z ==> Vertex 2 {m}
> 3.7,3.7,0.0, !- X,Y,Z ==> Vertex 3 {m}
> 3.7,3.7,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> RIGHT-1, !- Name
> Wall, !- Surface Type
> WALL-1, !- Construction Name
> EAST PERIMETER, !- Zone Name
> Outdoors, !- Outside Boundary Condition
> , !- Outside Boundary Condition Object
> SunExposed, !- Sun Exposure
> WindExposed, !- Wind Exposure
> 0.50000, !- View Factor to Ground
> 4, !- Number of Vertices
> 30.5,0.0,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 30.5,0.0,0.0, !- X,Y,Z ==> Vertex 2 {m}
> 30.5,15.2,0.0, !- X,Y,Z ==> Vertex 3 {m}
> 30.5,15.2,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> C2-1, !- Name
> Ceiling, !- Surface Type
> CLNG-1, !- Construction Name
> EAST PERIMETER, !- Zone Name
> Surface, !- Outside Boundary Condition
> C2-1P, !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 26.8,3.7,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 30.5,0.0,2.4, !- X,Y,Z ==> Vertex 2 {m}
> 30.5,15.2,2.4, !- X,Y,Z ==> Vertex 3 {m}
> 26.8,11.6,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> F2-1, !- Name
> Floor, !- Surface Type
> FLOOR-SLAB-1, !- Construction Name
> EAST PERIMETER, !- Zone Name
> Ground, !- Outside Boundary Condition
> , !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 26.8,11.6,0.0, !- X,Y,Z ==> Vertex 1 {m}
> 30.5,15.2,0.0, !- X,Y,Z ==> Vertex 2 {m}
> 30.5,0.0,0.0, !- X,Y,Z ==> Vertex 3 {m}
> 26.8,3.7,0.0; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> SB21, !- Name
> Wall, !- Surface Type
> INT-WALL-1, !- Construction Name
> EAST PERIMETER, !- Zone Name
> Surface, !- Outside Boundary Condition
> SB12, !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 26.8,3.7,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 26.8,3.7,0.0, !- X,Y,Z ==> Vertex 2 {m}
> 30.5,0.0,0.0, !- X,Y,Z ==> Vertex 3 {m}
> 30.5,0.0,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> SB23, !- Name
> Wall, !- Surface Type
> INT-WALL-1, !- Construction Name
> EAST PERIMETER, !- Zone Name
> Surface, !- Outside Boundary Condition
> SB32, !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 30.5,15.2,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 30.5,15.2,0.0, !- X,Y,Z ==> Vertex 2 {m}
> 26.8,11.6,0.0, !- X,Y,Z ==> Vertex 3 {m}
> 26.8,11.6,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> SB25, !- Name
> Wall, !- Surface Type
> INT-WALL-1, !- Construction Name
> EAST PERIMETER, !- Zone Name
> Surface, !- Outside Boundary Condition
> SB52, !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 26.8,11.6,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 26.8,11.6,0.0, !- X,Y,Z ==> Vertex 2 {m}
> 26.8,3.7,0.0, !- X,Y,Z ==> Vertex 3 {m}
> 26.8,3.7,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> BACK-1, !- Name
> Wall, !- Surface Type
> WALL-1, !- Construction Name
> NORTH PERIMETER, !- Zone Name
> Outdoors, !- Outside Boundary Condition
> , !- Outside Boundary Condition Object
> SunExposed, !- Sun Exposure
> WindExposed, !- Wind Exposure
> 0.50000, !- View Factor to Ground
> 4, !- Number of Vertices
> 30.5,15.2,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 30.5,15.2,0.0, !- X,Y,Z ==> Vertex 2 {m}
> 0.0,15.2,0.0, !- X,Y,Z ==> Vertex 3 {m}
> 0.0,15.2,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> C3-1, !- Name
> Ceiling, !- Surface Type
> CLNG-1, !- Construction Name
> NORTH PERIMETER, !- Zone Name
> Surface, !- Outside Boundary Condition
> C3-1P, !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 30.5,15.2,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 0.0,15.2,2.4, !- X,Y,Z ==> Vertex 2 {m}
> 3.7,11.6,2.4, !- X,Y,Z ==> Vertex 3 {m}
> 26.8,11.6,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> F3-1, !- Name
> Floor, !- Surface Type
> FLOOR-SLAB-1, !- Construction Name
> NORTH PERIMETER, !- Zone Name
> Ground, !- Outside Boundary Condition
> , !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 26.8,11.6,0.0, !- X,Y,Z ==> Vertex 1 {m}
> 3.7,11.6,0.0, !- X,Y,Z ==> Vertex 2 {m}
> 0.0,15.2,0.0, !- X,Y,Z ==> Vertex 3 {m}
> 30.5,15.2,0.0; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> SB32, !- Name
> Wall, !- Surface Type
> INT-WALL-1, !- Construction Name
> NORTH PERIMETER, !- Zone Name
> Surface, !- Outside Boundary Condition
> SB23, !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 26.8,11.6,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 26.8,11.6,0.0, !- X,Y,Z ==> Vertex 2 {m}
> 30.5,15.2,0.0, !- X,Y,Z ==> Vertex 3 {m}
> 30.5,15.2,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> SB34, !- Name
> Wall, !- Surface Type
> INT-WALL-1, !- Construction Name
> NORTH PERIMETER, !- Zone Name
> Surface, !- Outside Boundary Condition
> SB43, !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 0.0,15.2,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 0.0,15.2,0.0, !- X,Y,Z ==> Vertex 2 {m}
> 3.7,11.6,0.0, !- X,Y,Z ==> Vertex 3 {m}
> 3.7,11.6,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> SB35, !- Name
> Wall, !- Surface Type
> INT-WALL-1, !- Construction Name
> NORTH PERIMETER, !- Zone Name
> Surface, !- Outside Boundary Condition
> SB53, !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 3.7,11.6,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 3.7,11.6,0.0, !- X,Y,Z ==> Vertex 2 {m}
> 26.8,11.6,0.0, !- X,Y,Z ==> Vertex 3 {m}
> 26.8,11.6,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> LEFT-1, !- Name
> Wall, !- Surface Type
> WALL-1, !- Construction Name
> WEST PERIMETER, !- Zone Name
> Outdoors, !- Outside Boundary Condition
> , !- Outside Boundary Condition Object
> SunExposed, !- Sun Exposure
> WindExposed, !- Wind Exposure
> 0.50000, !- View Factor to Ground
> 4, !- Number of Vertices
> 0.0,15.2,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 0.0,15.2,0.0, !- X,Y,Z ==> Vertex 2 {m}
> 0.0,0.0,0.0, !- X,Y,Z ==> Vertex 3 {m}
> 0.0,0.0,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> C4-1, !- Name
> Ceiling, !- Surface Type
> CLNG-1, !- Construction Name
> WEST PERIMETER, !- Zone Name
> Surface, !- Outside Boundary Condition
> C4-1P, !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 3.7,11.6,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 0.0,15.2,2.4, !- X,Y,Z ==> Vertex 2 {m}
> 0.0,0.0,2.4, !- X,Y,Z ==> Vertex 3 {m}
> 3.7,3.7,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> F4-1, !- Name
> Floor, !- Surface Type
> FLOOR-SLAB-1, !- Construction Name
> WEST PERIMETER, !- Zone Name
> Ground, !- Outside Boundary Condition
> , !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 3.7,3.7,0.0, !- X,Y,Z ==> Vertex 1 {m}
> 0.0,0.0,0.0, !- X,Y,Z ==> Vertex 2 {m}
> 0.0,15.2,0.0, !- X,Y,Z ==> Vertex 3 {m}
> 3.7,11.6,0.0; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> SB41, !- Name
> Wall, !- Surface Type
> INT-WALL-1, !- Construction Name
> WEST PERIMETER, !- Zone Name
> Surface, !- Outside Boundary Condition
> SB14, !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 0.0,0.0,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 0.0,0.0,0.0, !- X,Y,Z ==> Vertex 2 {m}
> 3.7,3.7,0.0, !- X,Y,Z ==> Vertex 3 {m}
> 3.7,3.7,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> SB43, !- Name
> Wall, !- Surface Type
> INT-WALL-1, !- Construction Name
> WEST PERIMETER, !- Zone Name
> Surface, !- Outside Boundary Condition
> SB34, !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 3.7,11.6,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 3.7,11.6,0.0, !- X,Y,Z ==> Vertex 2 {m}
> 0.0,15.2,0.0, !- X,Y,Z ==> Vertex 3 {m}
> 0.0,15.2,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> SB45, !- Name
> Wall, !- Surface Type
> INT-WALL-1, !- Construction Name
> WEST PERIMETER, !- Zone Name
> Surface, !- Outside Boundary Condition
> SB54, !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 3.7,3.7,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 3.7,3.7,0.0, !- X,Y,Z ==> Vertex 2 {m}
> 3.7,11.6,0.0, !- X,Y,Z ==> Vertex 3 {m}
> 3.7,11.6,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> C5-1, !- Name
> Ceiling, !- Surface Type
> CLNG-1, !- Construction Name
> CORE, !- Zone Name
> Surface, !- Outside Boundary Condition
> C5-1P, !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 3.7,11.6,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 3.7,3.7,2.4, !- X,Y,Z ==> Vertex 2 {m}
> 26.8,3.7,2.4, !- X,Y,Z ==> Vertex 3 {m}
> 26.8,11.6,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> F5-1, !- Name
> Floor, !- Surface Type
> FLOOR-SLAB-1, !- Construction Name
> CORE, !- Zone Name
> Ground, !- Outside Boundary Condition
> , !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 26.8,11.6,0.0, !- X,Y,Z ==> Vertex 1 {m}
> 26.8,3.7,0.0, !- X,Y,Z ==> Vertex 2 {m}
> 3.7,3.7,0.0, !- X,Y,Z ==> Vertex 3 {m}
> 3.7,11.6,0.0; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> SB51, !- Name
> Wall, !- Surface Type
> INT-WALL-1, !- Construction Name
> CORE, !- Zone Name
> Surface, !- Outside Boundary Condition
> SB15, !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 3.7,3.7,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 3.7,3.7,0.0, !- X,Y,Z ==> Vertex 2 {m}
> 26.8,3.7,0.0, !- X,Y,Z ==> Vertex 3 {m}
> 26.8,3.7,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> SB52, !- Name
> Wall, !- Surface Type
> INT-WALL-1, !- Construction Name
> CORE, !- Zone Name
> Surface, !- Outside Boundary Condition
> SB25, !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 26.8,3.7,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 26.8,3.7,0.0, !- X,Y,Z ==> Vertex 2 {m}
> 26.8,11.6,0.0, !- X,Y,Z ==> Vertex 3 {m}
> 26.8,11.6,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> SB53, !- Name
> Wall, !- Surface Type
> INT-WALL-1, !- Construction Name
> CORE, !- Zone Name
> Surface, !- Outside Boundary Condition
> SB35, !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 26.8,11.6,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 26.8,11.6,0.0, !- X,Y,Z ==> Vertex 2 {m}
> 3.7,11.6,0.0, !- X,Y,Z ==> Vertex 3 {m}
> 3.7,11.6,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> BuildingSurface:Detailed,
> SB54, !- Name
> Wall, !- Surface Type
> INT-WALL-1, !- Construction Name
> CORE, !- Zone Name
> Surface, !- Outside Boundary Condition
> SB45, !- Outside Boundary Condition Object
> NoSun, !- Sun Exposure
> NoWind, !- Wind Exposure
> 0.0, !- View Factor to Ground
> 4, !- Number of Vertices
> 3.7,11.6,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 3.7,11.6,0.0, !- X,Y,Z ==> Vertex 2 {m}
> 3.7,3.7,0.0, !- X,Y,Z ==> Vertex 3 {m}
> 3.7,3.7,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> FenestrationSurface:Detailed,
> WF-1, !- Name
> Window, !- Surface Type
> Double LoE Clear Argon, !- Construction Name
> FRONT-1, !- Building Surface Name
> , !- Outside Boundary Condition Object
> 0.50000, !- View Factor to Ground
> , !- Shading Control Name
> , !- Frame and Divider Name
> 1, !- Multiplier
> 4, !- Number of Vertices
> 3.0,0.0,2.1, !- X,Y,Z ==> Vertex 1 {m}
> 3.0,0.0,0.9, !- X,Y,Z ==> Vertex 2 {m}
> 16.8,0.0,0.9, !- X,Y,Z ==> Vertex 3 {m}
> 16.8,0.0,2.1; !- X,Y,Z ==> Vertex 4 {m}
>
> FenestrationSurface:Detailed,
> DF-1, !- Name
> Window, !- Surface Type
> Double LoE Clear Argon, !- Construction Name
> FRONT-1, !- Building Surface Name
> , !- Outside Boundary Condition Object
> 0.50000, !- View Factor to Ground
> , !- Shading Control Name
> , !- Frame and Divider Name
> 1, !- Multiplier
> 4, !- Number of Vertices
> 21.3,0.0,2.4, !- X,Y,Z ==> Vertex 1 {m}
> 21.3,0.0,0.0, !- X,Y,Z ==> Vertex 2 {m}
> 23.8,0.0,0.0, !- X,Y,Z ==> Vertex 3 {m}
> 23.8,0.0,2.4; !- X,Y,Z ==> Vertex 4 {m}
>
> FenestrationSurface:Detailed,
> WR-1, !- Name
> Window, !- Surface Type
> Double LoE Clear Argon, !- Construction Name
> RIGHT-1, !- Building Surface Name
> , !- Outside Boundary Condition Object
> 0.50000, !- View Factor to Ground
> , !- Shading Control Name
> , !- Frame and Divider Name
> 1, !- Multiplier
> 4, !- Number of Vertices
> 30.5,3.8,2.1, !- X,Y,Z ==> Vertex 1 {m}
> 30.5,3.8,0.9, !- X,Y,Z ==> Vertex 2 {m}
> 30.5,11.4,0.9, !- X,Y,Z ==> Vertex 3 {m}
> 30.5,11.4,2.1; !- X,Y,Z ==> Vertex 4 {m}
>
> FenestrationSurface:Detailed,
> WB-1, !- Name
> Window, !- Surface Type
> Double LoE Clear Argon, !- Construction Name
> BACK-1, !- Building Surface Name
> , !- Outside Boundary Condition Object
> 0.50000, !- View Factor to Ground
> , !- Shading Control Name
> , !- Frame and Divider Name
> 1, !- Multiplier
> 4, !- Number of Vertices
> 27.4,15.2,2.1, !- X,Y,Z ==> Vertex 1 {m}
> 27.4,15.2,0.9, !- X,Y,Z ==> Vertex 2 {m}
> 13.7,15.2,0.9, !- X,Y,Z ==> Vertex 3 {m}
> 13.7,15.2,2.1; !- X,Y,Z ==> Vertex 4 {m}
>
> FenestrationSurface:Detailed,
> DB-1, !- Name
> Window, !- Surface Type
> Double LoE Clear Argon, !- Construction Name
> BACK-1, !- Building Surface Name
> , !- Outside Boundary Condition Object
> 0.50000, !- View Factor to Ground
> , !- Shading Control Name
> , !- Frame and Divider Name
> 1, !- Multiplier
> 4, !- Number of Vertices
> 9.1,15.2,2.1, !- X,Y,Z ==> Vertex 1 {m}
> 9.1,15.2,0.0, !- X,Y,Z ==> Vertex 2 {m}
> 7.0,15.2,0.0, !- X,Y,Z ==> Vertex 3 {m}
> 7.0,15.2,2.1; !- X,Y,Z ==> Vertex 4 {m}
>
> FenestrationSurface:Detailed,
> WL-1, !- Name
> Window, !- Surface Type
> Double LoE Clear Argon, !- Construction Name
> LEFT-1, !- Building Surface Name
> , !- Outside Boundary Condition Object
> 0.50000, !- View Factor to Ground
> , !- Shading Control Name
> , !- Frame and Divider Name
> 1, !- Multiplier
> 4, !- Number of Vertices
> 0.0,11.4,2.1, !- X,Y,Z ==> Vertex 1 {m}
> 0.0,11.4,0.9, !- X,Y,Z ==> Vertex 2 {m}
> 0.0,3.8,0.9, !- X,Y,Z ==> Vertex 3 {m}
> 0.0,3.8,2.1; !- X,Y,Z ==> Vertex 4 {m}
>
> Shading:Zone:Detailed,
> Main South Overhang, !- Name
> FRONT-1, !- Base Surface Name
> ShadeTransSch, !- Transmittance Schedule Name
> 4, !- Number of Vertices
> 0.0,-1.3,2.2, !- X,Y,Z ==> Vertex 1 {m}
> 0.0,0.0,2.2, !- X,Y,Z ==> Vertex 2 {m}
> 19.8,0.0,2.2, !- X,Y,Z ==> Vertex 3 {m}
> 19.8,-1.3,2.2; !- X,Y,Z ==> Vertex 4 {m}
>
> Shading:Zone:Detailed,
> South Door Overhang, !- Name
> FRONT-1, !- Base Surface Name
> ShadeTransSch, !- Transmittance Schedule Name
> 4, !- Number of Vertices
> 21.0,-2.0,2.6, !- X,Y,Z ==> Vertex 1 {m}
> 21.0,0.0,2.6, !- X,Y,Z ==> Vertex 2 {m}
> 24.1,0.0,2.6, !- X,Y,Z ==> Vertex 3 {m}
> 24.1,-2.0,2.6; !- X,Y,Z ==> Vertex 4 {m}
>
> ScheduleTypeLimits,
> Any Number; !- Name
>
> ScheduleTypeLimits,
> Fraction, !- Name
> 0.0, !- Lower Limit Value
> 1.0, !- Upper Limit Value
> Continuous; !- Numeric Type
>
> ScheduleTypeLimits,
> Temperature, !- Name
> -60, !- Lower Limit Value
> 200, !- Upper Limit Value
> Continuous; !- Numeric Type
>
> ScheduleTypeLimits,
> On/Off, !- Name
> 0, !- Lower Limit Value
> 1, !- Upper Limit Value
> Discrete; !- Numeric Type
>
> Schedule:Compact,
> Constant, !- Name
> on/off, !- Schedule Type Limits Name
> Through: 12/31, !- Field 1
> For: AllDays, !- Field 2
> Until: 24:00,1.0; !- Field 3
>
> Schedule:Compact,
> Office HVAC, !- Name
> on/off, !- Schedule Type Limits Name
> Through: 12/31, !- Field 1
> For: Weekdays SummerDesignDay, !- Field 2
> Until: 06:00,0.0, !- Field 3
> Until: 22:00,1.0, !- Field 5
> Until: 24:00,0.0, !- Field 7
> For: Saturday WinterDesignDay, !- Field 9
> Until: 06:00,0.0, !- Field 10
> Until: 18:00,1.0, !- Field 12
> Until: 24:00,0.0, !- Field 14
> For: Sunday Holidays AllOtherDays, !- Field 16
> Until: 24:00,0.0; !- Field 17
>
> Schedule:Compact,
> Office Heating Setpoints,!- Name
> Temperature, !- Schedule Type Limits Name
> Through: 12/31, !- Field 1
> For: Weekdays, !- Field 2
> Until: 06:00,12.8, !- Field 3
> Until: 22:00,21.1, !- Field 5
> Until: 24:00,12.8, !- Field 7
> For: Saturday, !- Field 9
> Until: 06:00,12.8, !- Field 10
> Until: 18:00,21.1, !- Field 12
> Until: 24:00,12.8, !- Field 14
> For: SummerDesignDay, !- Field 16
> Until: 24:00,12.8, !- Field 17
> For: WinterDesignDay, !- Field 19
> Until: 24:00,21.1, !- Field 20
> For: Sunday Holidays AllOtherDays, !- Field 22
> Until: 24:00,12.8; !- Field 23
>
> Schedule:Compact,
> Office Cooling Setpoints,!- Name
> Temperature, !- Schedule Type Limits Name
> Through: 12/31, !- Field 1
> For: Weekdays, !- Field 2
> Until: 06:00,40.0, !- Field 3
> Until: 22:00,23.9, !- Field 5
> Until: 24:00,40.0, !- Field 7
> For: Saturday, !- Field 9
> Until: 06:00,40.0, !- Field 10
> Until: 18:00,23.9, !- Field 12
> Until: 24:00,40.0, !- Field 14
> For: SummerDesignDay, !- Field 16
> Until: 24:00,23.9, !- Field 17
> For: WinterDesignDay, !- Field 19
> Until: 24:00,40.0, !- Field 20
> For: Sunday Holidays AllOtherDays, !- Field 22
> Until: 24:00,40.0; !- Field 23
>
> Schedule:Compact,
> Office Minimum OA, !- Name
> on/off, !- Schedule Type Limits Name
> Through: 12/31, !- Field 1
> For: Weekdays SummerDesignDay, !- Field 2
> Until: 07:00,0.0, !- Field 3
> Until: 22:00,1.0, !- Field 5
> Until: 24:00,0.0, !- Field 7
> For: Saturday WinterDesignDay, !- Field 9
> Until: 07:00,0.0, !- Field 10
> Until: 18:00,1.0, !- Field 12
> Until: 24:00,0.0, !- Field 14
> For: Sunday Holidays AllOtherDays, !- Field 16
> Until: 24:00,0.0; !- Field 17
>
> Schedule:Compact,
> Office Lighting 2, !- Name
> Fraction, !- Schedule Type Limits Name
> Through: 12/31, !- Field 1
> For: Weekdays SummerDesignDay, !- Field 2
> Until: 05:00,0.05, !- Field 3
> Until: 07:00,0.1, !- Field 5
> Until: 08:00,0.3, !- Field 7
> Until: 17:00,0.9, !- Field 9
> Until: 18:00,0.5, !- Field 11
> Until: 20:00,0.3, !- Field 13
> Until: 22:00,0.2, !- Field 15
> Until: 23:00,0.1, !- Field 17
> Until: 24:00,0.05, !- Field 19
> For: Saturday, !- Field 21
> Until: 06:00,0.05, !- Field 22
> Until: 08:00,0.1, !- Field 24
> Until: 12:00,0.3, !- Field 26
> Until: 17:00,0.15, !- Field 28
> Until: 24:00,0.05, !- Field 30
> For: WinterDesignDay, !- Field 32
> Until: 24:00,0.0, !- Field 33
> For: Sunday Holidays AllOtherDays, !- Field 35
> Until: 24:00,0.05; !- Field 36
>
> Schedule:Compact,
> Office Occupancy 2, !- Name
> Fraction, !- Schedule Type Limits Name
> Through: 12/31, !- Field 1
> For: Weekdays SummerDesignDay, !- Field 2
> Until: 07:00,0.0, !- Field 3
> Until: 08:00,0.2, !- Field 5
> Until: 12:00,0.95, !- Field 7
> Until: 13:00,0.5, !- Field 9
> Until: 17:00,0.95, !- Field 11
> Until: 18:00,0.3, !- Field 13
> Until: 22:00,0.1, !- Field 15
> Until: 24:00,0.0, !- Field 17
> For: Saturday, !- Field 19
> Until: 07:00,0.0, !- Field 20
> Until: 08:00,0.1, !- Field 22
> Until: 12:00,0.3, !- Field 24
> Until: 17:00,0.1, !- Field 26
> Until: 18:00,0.05, !- Field 28
> Until: 24:00,0.0, !- Field 30
> For: Sunday Holidays WinterDesignDay AllOtherDays, !- Field 32
> Until: 24:00,0.0; !- Field 33
>
> Schedule:Compact,
> ActSchd, !- Name
> Any Number, !- Schedule Type Limits Name
> Through: 12/31, !- Field 1
> For: AllDays, !- Field 2
> Until: 24:00,117.239997864; !- Field 3
>
> !- Complex Field #4
>
> Schedule:Compact,
> ShadeTransSch, !- Name
> Fraction, !- Schedule Type Limits Name
> Through: 12/31, !- Field 1
> For: AllDays, !- Field 2
> Until: 24:00,0.0; !- Field 3
>
> Schedule:Compact,
> Seasonal Reset Supply Air Temp Sch, !- Name
> Temperature, !- Schedule Type Limits Name
> Through: 3/31, !- Field 1
> For: AllDays, !- Field 2
> Until: 24:00,16.0, !- Field 3
> Through: 9/30, !- Field 5
> For: AllDays, !- Field 6
> Until: 24:00,13.0, !- Field 7
> Through: 12/31, !- Field 9
> For: AllDays, !- Field 10
> Until: 24:00,16.0; !- Field 11
>
> People,
> SOUTH PERIMETER People 1,!- Name
> SOUTH PERIMETER, !- Zone or ZoneList Name
> Office Occupancy 2, !- Number of People Schedule Name
> People, !- Number of People Calculation Method
> 11, !- Number of People
> , !- People per Zone Floor Area {person/m2}
> , !- Zone Floor Area per Person {m2/person}
> 0.3, !- Fraction Radiant
> , !- Sensible Heat Fraction
> ActSchd; !- Activity Level Schedule Name
>
> People,
> EAST PERIMETER People 1, !- Name
> EAST PERIMETER, !- Zone or ZoneList Name
> Office Occupancy 2, !- Number of People Schedule Name
> People, !- Number of People Calculation Method
> 5, !- Number of People
> , !- People per Zone Floor Area {person/m2}
> , !- Zone Floor Area per Person {m2/person}
> 0.3, !- Fraction Radiant
> , !- Sensible Heat Fraction
> ActSchd; !- Activity Level Schedule Name
>
> People,
> NORTH PERIMETER People 1,!- Name
> NORTH PERIMETER, !- Zone or ZoneList Name
> Office Occupancy 2, !- Number of People Schedule Name
> People, !- Number of People Calculation Method
> 11, !- Number of People
> , !- People per Zone Floor Area {person/m2}
> , !- Zone Floor Area per Person {m2/person}
> 0.3, !- Fraction Radiant
> , !- Sensible Heat Fraction
> ActSchd; !- Activity Level Schedule Name
>
> People,
> WEST PERIMETER People 1, !- Name
> WEST PERIMETER, !- Zone or ZoneList Name
> Office Occupancy 2, !- Number of People Schedule Name
> People, !- Number of People Calculation Method
> 5, !- Number of People
> , !- People per Zone Floor Area {person/m2}
> , !- Zone Floor Area per Person {m2/person}
> 0.3, !- Fraction Radiant
> , !- Sensible Heat Fraction
> ActSchd; !- Activity Level Schedule Name
>
> People,
> CORE People 1, !- Name
> CORE, !- Zone or ZoneList Name
> Office Occupancy 2, !- Number of People Schedule Name
> People, !- Number of People Calculation Method
> 20, !- Number of People
> , !- People per Zone Floor Area {person/m2}
> , !- Zone Floor Area per Person {m2/person}
> 0.3, !- Fraction Radiant
> , !- Sensible Heat Fraction
> ActSchd; !- Activity Level Schedule Name
>
> Lights,
> SOUTH PERIMETER Lights 1,!- Name
> SOUTH PERIMETER, !- Zone or ZoneList Name
> Office Lighting 2, !- Schedule Name
> LightingLevel, !- Design Level Calculation Method
> 1584, !- Lighting Level {W}
> , !- Watts per Zone Floor Area {W/m2}
> , !- Watts per Person {W/person}
> 0.2, !- Return Air Fraction
> 0.59, !- Fraction Radiant
> 0.2, !- Fraction Visible
> 0, !- Fraction Replaceable
> GeneralLights; !- End-Use Subcategory
>
> Lights,
> EAST PERIMETER Lights 1, !- Name
> EAST PERIMETER, !- Zone or ZoneList Name
> Office Lighting 2, !- Schedule Name
> LightingLevel, !- Design Level Calculation Method
> 684, !- Lighting Level {W}
> , !- Watts per Zone Floor Area {W/m2}
> , !- Watts per Person {W/person}
> 0.2, !- Return Air Fraction
> 0.59, !- Fraction Radiant
> 0.2, !- Fraction Visible
> 0, !- Fraction Replaceable
> GeneralLights; !- End-Use Subcategory
>
> Lights,
> NORTH PERIMETER Lights 1,!- Name
> NORTH PERIMETER, !- Zone or ZoneList Name
> Office Lighting 2, !- Schedule Name
> LightingLevel, !- Design Level Calculation Method
> 1584, !- Lighting Level {W}
> , !- Watts per Zone Floor Area {W/m2}
> , !- Watts per Person {W/person}
> 0.2, !- Return Air Fraction
> 0.59, !- Fraction Radiant
> 0.2, !- Fraction Visible
> 0, !- Fraction Replaceable
> GeneralLights; !- End-Use Subcategory
>
> Lights,
> WEST PERIMETER Lights 1, !- Name
> WEST PERIMETER, !- Zone or ZoneList Name
> Office Lighting 2, !- Schedule Name
> LightingLevel, !- Design Level Calculation Method
> 684, !- Lighting Level {W}
> , !- Watts per Zone Floor Area {W/m2}
> , !- Watts per Person {W/person}
> 0.2, !- Return Air Fraction
> 0.59, !- Fraction Radiant
> 0.2, !- Fraction Visible
> 0, !- Fraction Replaceable
> GeneralLights; !- End-Use Subcategory
>
> Lights,
> CORE Lights 1, !- Name
> CORE, !- Zone or ZoneList Name
> Office Lighting 2, !- Schedule Name
> LightingLevel, !- Design Level Calculation Method
> 2964, !- Lighting Level {W}
> , !- Watts per Zone Floor Area {W/m2}
> , !- Watts per Person {W/person}
> 0.2, !- Return Air Fraction
> 0.59, !- Fraction Radiant
> 0.2, !- Fraction Visible
> 0, !- Fraction Replaceable
> GeneralLights; !- End-Use Subcategory
>
> ElectricEquipment,
> SOUTH PERIMETER ElecEq 1,!- Name
> SOUTH PERIMETER, !- Zone or ZoneList Name
> Office Lighting 2, !- Schedule Name
> EquipmentLevel, !- Design Level Calculation Method
> 1056, !- Design Level {W}
> , !- Watts per Zone Floor Area {W/m2}
> , !- Watts per Person {W/person}
> 0, !- Fraction Latent
> 0.3, !- Fraction Radiant
> 0, !- Fraction Lost
> General; !- End-Use Subcategory
>
> ElectricEquipment,
> EAST PERIMETER ElecEq 1, !- Name
> EAST PERIMETER, !- Zone or ZoneList Name
> Office Lighting 2, !- Schedule Name
> EquipmentLevel, !- Design Level Calculation Method
> 456, !- Design Level {W}
> , !- Watts per Zone Floor Area {W/m2}
> , !- Watts per Person {W/person}
> 0, !- Fraction Latent
> 0.3, !- Fraction Radiant
> 0, !- Fraction Lost
> General; !- End-Use Subcategory
>
> ElectricEquipment,
> NORTH PERIMETER ElecEq 1,!- Name
> NORTH PERIMETER, !- Zone or ZoneList Name
> Office Lighting 2, !- Schedule Name
> EquipmentLevel, !- Design Level Calculation Method
> 1056, !- Design Level {W}
> , !- Watts per Zone Floor Area {W/m2}
> , !- Watts per Person {W/person}
> 0, !- Fraction Latent
> 0.3, !- Fraction Radiant
> 0, !- Fraction Lost
> General; !- End-Use Subcategory
>
> ElectricEquipment,
> WEST PERIMETER ElecEq 1, !- Name
> WEST PERIMETER, !- Zone or ZoneList Name
> Office Lighting 2, !- Schedule Name
> EquipmentLevel, !- Design Level Calculation Method
> 456, !- Design Level {W}
> , !- Watts per Zone Floor Area {W/m2}
> , !- Watts per Person {W/person}
> 0, !- Fraction Latent
> 0.3, !- Fraction Radiant
> 0, !- Fraction Lost
> General; !- End-Use Subcategory
>
> ElectricEquipment,
> CORE ElecEq 1, !- Name
> CORE, !- Zone or ZoneList Name
> Office Lighting 2, !- Schedule Name
> EquipmentLevel, !- Design Level Calculation Method
> 1976, !- Design Level {W}
> , !- Watts per Zone Floor Area {W/m2}
> , !- Watts per Person {W/person}
> 0, !- Fraction Latent
> 0.3, !- Fraction Radiant
> 0, !- Fraction Lost
> General; !- End-Use Subcategory
>
> ZoneInfiltration:DesignFlowRate,
> SOUTH PERIMETER Infil 1, !- Name
> SOUTH PERIMETER, !- Zone or ZoneList Name
> Constant, !- Schedule Name
> Flow/Zone, !- Design Flow Rate Calculation Method
> 0.035, !- Design Flow Rate {m3/s}
> , !- Flow per Zone Floor Area {m3/s-m2}
> , !- Flow per Exterior Surface Area {m3/s-m2}
> , !- Air Changes per Hour
> 0, !- Constant Term Coefficient
> 0, !- Temperature Term Coefficient
> 0.2237, !- Velocity Term Coefficient
> 0; !- Velocity Squared Term Coefficient
>
> ZoneInfiltration:DesignFlowRate,
> EAST PERIMETER Infil 1, !- Name
> EAST PERIMETER, !- Zone or ZoneList Name
> Constant, !- Schedule Name
> Flow/Zone, !- Design Flow Rate Calculation Method
> 0.015, !- Design Flow Rate {m3/s}
> , !- Flow per Zone Floor Area {m3/s-m2}
> , !- Flow per Exterior Surface Area {m3/s-m2}
> , !- Air Changes per Hour
> 0, !- Constant Term Coefficient
> 0, !- Temperature Term Coefficient
> 0.2237, !- Velocity Term Coefficient
> 0; !- Velocity Squared Term Coefficient
>
> ZoneInfiltration:DesignFlowRate,
> NORTH PERIMETER Infil 1, !- Name
> NORTH PERIMETER, !- Zone or ZoneList Name
> Constant, !- Schedule Name
> Flow/Zone, !- Design Flow Rate Calculation Method
> 0.035, !- Design Flow Rate {m3/s}
> , !- Flow per Zone Floor Area {m3/s-m2}
> , !- Flow per Exterior Surface Area {m3/s-m2}
> , !- Air Changes per Hour
> 0, !- Constant Term Coefficient
> 0, !- Temperature Term Coefficient
> 0.2237, !- Velocity Term Coefficient
> 0; !- Velocity Squared Term Coefficient
>
> ZoneInfiltration:DesignFlowRate,
> WEST PERIMETER Infil 1, !- Name
> WEST PERIMETER, !- Zone or ZoneList Name
> Constant, !- Schedule Name
> Flow/Zone, !- Design Flow Rate Calculation Method
> 0.015, !- Design Flow Rate {m3/s}
> , !- Flow per Zone Floor Area {m3/s-m2}
> , !- Flow per Exterior Surface Area {m3/s-m2}
> , !- Air Changes per Hour
> 0, !- Constant Term Coefficient
> 0, !- Temperature Term Coefficient
> 0.2237, !- Velocity Term Coefficient
> 0; !- Velocity Squared Term Coefficient
>
> ZoneInfiltration:DesignFlowRate,
> CORE Infil 1, !- Name
> CORE, !- Zone or ZoneList Name
> Constant, !- Schedule Name
> Flow/Zone, !- Design Flow Rate Calculation Method
> 0.062, !- Design Flow Rate {m3/s}
> , !- Flow per Zone Floor Area {m3/s-m2}
> , !- Flow per Exterior Surface Area {m3/s-m2}
> , !- Air Changes per Hour
> 0, !- Constant Term Coefficient
> 0, !- Temperature Term Coefficient
> 0.2237, !- Velocity Term Coefficient
> 0; !- Velocity Squared Term Coefficient
>
> Output:Variable,*,Outdoor Dry Bulb,Monthly;
>
> Output:Variable,*,Zone/Sys Air Temperature,Monthly;
>
> Output:Variable,*,Zone/Sys Sensible Cooling Rate,Monthly;
>
> Output:Variable,*,Zone/Sys Sensible Heating Rate,Monthly;
>
> Output:Variable,*,Zone People Number Of Occupants,Monthly;
>
> Output:Variable,*,Zone Lights Total Heat Gain,Monthly;
>
> Output:Variable,*,Zone Electric Equipment Total Heat Gain,Monthly;
>
> Output:Variable,*,Zone Infiltration Air Change Rate,Monthly;
>
> Output:Variable,*,Zone Infiltration Sensible Heat Loss,Monthly;
>
> Output:Variable,*,Zone Infiltration Sensible Heat Gain,Monthly;
>
> Output:Meter:MeterFileOnly,Electricity:Facility,Monthly;
>
> Output:Meter:MeterFileOnly,Electricity:Building,Monthly;
>
> Output:Meter:MeterFileOnly,Electricity:HVAC,Monthly;
>
> Output:Meter:MeterFileOnly,Electricity:Plant,Monthly;
>
> Output:Meter:MeterFileOnly,Electricity:Facility,RunPeriod;
>
> Output:Meter:MeterFileOnly,Electricity:Building,RunPeriod;
>
> Output:Meter:MeterFileOnly,Electricity:HVAC,RunPeriod;
>
> Output:Meter:MeterFileOnly,Electricity:Plant,RunPeriod;
>
> Output:Meter:MeterFileOnly,Gas:Facility,Monthly;
>
> Output:Meter:MeterFileOnly,Gas:HVAC,Monthly;
>
> Output:Meter:MeterFileOnly,Gas:Plant,Monthly;
>
> Output:Meter:MeterFileOnly,Gas:Facility,RunPeriod;
>
> Output:Meter:MeterFileOnly,Gas:HVAC,RunPeriod;
>
> Output:Meter:MeterFileOnly,Gas:Plant,RunPeriod;
>
> Output:VariableDictionary,Regular;
>
> Output:Surfaces:Drawing,dxf;
>
> OutputControl:Table:Style,
> HTML; !- Column Separator
>
> Output:Table:SummaryReports,
> ABUPS, !- Report 1 Name
> EquipmentSummary; !- Report 2 Name
>
------------------------------------
Primary EnergyPlus support is found at:
http://energyplus.helpserve.com or send a message to energyplus-support@xxxxxxxx
The primary EnergyPlus web site is found at:
http://www.energyplus.gov
The group web site is:
http://groups.yahoo.com/group/EnergyPlus_Support/
Attachments are currently allowed but be mindful that not everyone has a high speed connection. Limit attachments to small files.
EnergyPlus Documentation is searchable. Open EPlusMainMenu.pdf under the Documentation link and press the "search" button.
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/EnergyPlus_Support/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/EnergyPlus_Support/join
(Yahoo! ID required)
<*> To change settings via email:
EnergyPlus_Support-digest@xxxxxxxxxxxxxxx
EnergyPlus_Support-fullfeatured@xxxxxxxxxxxxxxx
<*> To unsubscribe from this group, send an email to:
EnergyPlus_Support-unsubscribe@xxxxxxxxxxxxxxx
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/