If you remove the terminal unit heating coils, you can no longer control the air loop heating coil at a constant supply air temperature (i.e., using a scheduled temperature set point). Verify how the main heating coil is controlled (i'm guessing scheduled) and use a different type of set point manager to control it (e.g., SetpointManager:SingleZone:Heating).
On 7/11/2011 7:01 PM, n_junk wrote:
Hi! You are refering to "Central Heating Design Supply Air Temperature", right? I forgot to tell that I already had changed it to 20, 30, 40, 50 and even 70ºC and none of them hadn't change at all the interior temperature. If I use a high temperature and put again the reheat coils, the rooms sometimes even overheat, but without them the temperatures continues under 20ºC.
This is really odd, I don't know what is happening.
--- In EnergyPlus_Support@xxxxxxxxxxxxxxx, Vinay Devanathan <vinay.devanathan@...> wrote:
>
> The main heating coils setpoint temperature will be set such that it only
> heats air to a certain temp, (say around 15 - 16 C), so that the reheat
> coils can be sized for proper capacity to meet the load. When you remove the
> reheat coils, your supply air will obviously be under-heated as the main
> heating coil is not sized for that high capacity and will end up providing
> supply air at the setpoint temperature. You can look at what the heating
> coils design leaving air temperature by viewing the expidf file under
> Sizing:System object.
>
> On Mon, Jul 11, 2011 at 1:02 PM, n_junk@... <
> n_junk@...> wrote:
>
> > **
> >
> >
> > Hi!
> >
> > I'm trying to simulate an existing HVAC system which is similar to a VAV,
> > only with heating, without cooling coil or reheat coils. I'm using the HVAC
> > Template VAV Packaged.
> > The rooms' temperatures stay above 20ºC, like I configured in the
> > Thermostat, until I remove the reheat coils. When I do that the temperature
> > drops under 20ºC and only reaches it if there are internal loads.
> >
> > I have almost everything in autosize, except the maximum flow of the input
> > air (but autosize never reaches it, so I think the problem is not from
> > there).
> >
> > To see my problem just open this example file that comes with EnergyPlus:
> > HVACTemplate-5ZonePackagedVAV.idf. Then run a simulation and consult the
> > evolution of Zone Air Temperature for any of the conditioned zones and see
> > that it stays inside the temperatures of the Thermostat. After that go to
> > the file, remove the reheat coils of every zone (and deactivate the system
> > cooling coil), run the simulation again and compare the temperatures. You'll
> > see that now the temperatures stay under the Thermostat limit and only reach
> > it when the internal loads harm the room enough.
> >
> > I'm looking in the expidf file for days and I still don't know what is
> > wrong with it. Since I really have to remove the reheat coils, what can I do
> > to correct this problem?
> >
> > Thanks in advance!
> >
> >
> >
>
-- Richard A. Raustad Senior Research Engineer Florida Solar Energy Center University of Central Florida 1679 Clearlake Road Cocoa, FL 32922-5703 Phone: (321) 638-1454 Fax: (321) 638-1439 or 1010 Visit our web site at: http://www.fsec.ucf.edu UCF - From Promise to Prominence: Celebrating 40 Years
__._,_.___
Primary EnergyPlus support is found at:
http://energyplus.helpserve.com or send a message to energyplus-support@xxxxxxxx
The primary EnergyPlus web site is found at:
http://www.energyplus.gov
The group web site is:
http://groups.yahoo.com/group/EnergyPlus_Support/
Attachments are currently allowed but be mindful that not everyone has a high speed connection. Limit attachments to small files.
EnergyPlus Documentation is searchable. Open EPlusMainMenu.pdf under the Documentation link and press the "search" button.
Change settings via the Web (Yahoo! ID required)
Change settings via email: Switch delivery to Daily Digest | Switch to Fully Featured
Visit Your Group | Yahoo! Groups Terms of Use | Unsubscribe
__,_._,___