[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[EnergyPlus_Support] Re: which outputs are the most appropriate to know the temperature
thanks
--- In EnergyPlus_Support@xxxxxxxxxxxxxxx, YuanLu Li <yli006@...> wrote:
>
>
> The IdealLoadsAirSystem inject or remove heat directly into or from a zone to maintain the temperature to setpoint of the thermostat. The intake air is the minimum specified. There is no heat to recover. The relief is equal to the inlet OA, which may be less than a few per cent of the total cooling load.. You can reduce the inlet OA to zero and it is equivalent to full heat recovery. That is why, any thing you add will be less efficient than the IdealLoadsAirSystem.
>
> Dr. Li
> To: EnergyPlus_Support@xxxxxxxxxxxxxxx
> From: motabmx1@...
> Date: Tue, 18 Oct 2011 12:45:20 +0000
> Subject: [EnergyPlus_Support] Re: which outputs are the most appropriate to know the temperature
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
> To Dr Li,
>
>
>
> sorry a bother you again, I would like to ask you if you know if it is possible to take into account the present of a Heat recovery system using an Ideal HVAC object
>
>
>
> thanks again
>
>
>
> --- In EnergyPlus_Support@xxxxxxxxxxxxxxx, YuanLu Li <yli006@> wrote:
>
> >
>
> >
>
> > Please read the Getting Started manual.
>
> >
>
> > Which outside temperature? Hourly outdoor environment temperature for a TMY is in the weather file. Exterior temperature of a wall depends on material used, construction, solar radiation, surface convection coefficient, interior teperature and OD temperature. It is calculated for every timestep in a simulation run.To: EnergyPlus_Support@xxxxxxxxxxxxxxx
>
> > From: motabmx1@
>
> > Date: Tue, 18 Oct 2011 11:45:17 +0000
>
> > Subject: [EnergyPlus_Support] which outputs are the most appropriate to know the temperature
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> >
>
> > dear all,
>
> >
>
> >
>
> >
>
> > Could anyone please tell me what outputs are the most adequate to know the temperature of an internal surface in my case a floor and the internal temperature of a zone?, is it possible to ask energyplus for the outside temperature in an specific day?
>
> >
>
> >
>
> >
>
> > thanks
>
> >
>
> >
>
> >
>
> > all
>
> >
>
------------------------------------
Primary EnergyPlus support is found at:
http://energyplus.helpserve.com or send a message to energyplus-support@xxxxxxxx
The primary EnergyPlus web site is found at:
http://www.energyplus.gov
The group web site is:
http://groups.yahoo.com/group/EnergyPlus_Support/
Attachments are currently allowed but be mindful that not everyone has a high speed connection. Limit attachments to small files.
EnergyPlus Documentation is searchable. Open EPlusMainMenu.pdf under the Documentation link and press the "search" button.
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/EnergyPlus_Support/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/EnergyPlus_Support/join
(Yahoo! ID required)
<*> To change settings via email:
EnergyPlus_Support-digest@xxxxxxxxxxxxxxx
EnergyPlus_Support-fullfeatured@xxxxxxxxxxxxxxx
<*> To unsubscribe from this group, send an email to:
EnergyPlus_Support-unsubscribe@xxxxxxxxxxxxxxx
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/