[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [EnergyPlus_Support] Re: inevitable crash





As you also sent this to the Helpdesk, an answer was supplied from there.

At 02:05 PM 5/16/2012, Valentin Schmidt wrote:


Hi guys thanks for the advice, the thing is that the simulation crashes before the error files are even generated. At least this is what i think because ive been unable to open them, even trying what you suggested.

Ive attached the error reports the software shows, anyone knows whats going on?

thanks!

valentin.

--- In EnergyPlus_Support@xxxxxxxxxxxxxxx, Richard Raustad <RRaustad@...> wrote:
>
> And make sure other open windows of results are closed before you
> simulate again. Only some files cause problems.
>
> On 4/26/2012 4:07 PM, CleanTech Analytics wrote:
> >
> >
> > Check your .err file and it should tell you the issue.
> >
> > You can do this by choosing "view single file .err" or by using one of
> > the "create sets" output buttons and choosing the .err file.
> >
> > The .err file should be your first file to review prior to other files
> > so that you can see any issues...
> >
> > If the results in the .err file do not make since to you post back to
> > the list and myself or someone else will respond with advise- Best of luck
> >
> >
> > /Jeremiah D. Crossett/
> > /CleanTech Analytics/
> > /503-688-8951/
> > / www.cleantechanalytics.com/ < http://www.cleantechanalytics.com>
> >
> >
> > *
> >
> > This document may contain valuable information proprietary to
> > CleanTech Analytics which is private and confidential. It may not be
> > shared, copied, stored or transmitted in any form without the prior
> > written consent of CleanTech Analytics
> >
> > *
> >
> >
> >
> > On Thu, Apr 26, 2012 at 12:55 PM, tinoelargentino
> > <valentinsch@... <mailto:valentinsch@...>> wrote:
> >
> >     Hey guys, i´m new with e-plus, and while going through the
> >     tutorials in the getting started pdf I started getting crashes
> >     when trying to simulate the files. At the beginning simulations
> >     went ok, but then the same files that I had simulated earlier
> >     started crashing immediately. Even the included examples crash
> >     now. What may be the problem?
> >
> >     the run status reports:
> >
> >     C:\~\Exercise2A.idf
> >     No weather files
> >     Crashed
> >
> >     thats it...
> >
> >     any help will be useful!
> >
> >
> >
> >
> >
>
> --
> Richard A. Raustad
> Senior Research Engineer
> Florida Solar Energy Center
> University of Central Florida
> 1679 Clearlake Road
> Cocoa, FL  32922-5703
> Phone:   (321) 638-1454
> Fax:     (321) 638-1439 or 1010
> Visit our web site at: http://www.fsec.ucf.edu
>
> UCF - From Promise to Prominence: Celebrating 40 Years
>




Content-Type: image/jpeg; name="crash1.JPG"
Content-Disposition: attachment; filename="crash1.JPG"
X-Attachment-Id: f_h2atkeh70

Content-Type: image/jpeg; name="crash2.JPG"
Content-Disposition: attachment; filename="crash2.JPG"
X-Attachment-Id: f_h2atkhml1


__._,_.___


Primary EnergyPlus support is found at:
http://energyplus.helpserve.com or send a message to energyplus-support@xxxxxxxx

The primary EnergyPlus web site is found at:
http://www.energyplus.gov

The group web site is:
http://groups.yahoo.com/group/EnergyPlus_Support/

Attachments are currently allowed but be mindful that not everyone has a high speed connection.  Limit attachments to small files.

EnergyPlus Documentation is searchable.  Open EPlusMainMenu.pdf under the Documentation link and press the "search" button.




Your email settings: Individual Email|Traditional
Change settings via the Web (Yahoo! ID required)
Change settings via email: Switch delivery to Daily Digest | Switch to Fully Featured
Visit Your Group | Yahoo! Groups Terms of Use | Unsubscribe

__,_._,___