[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [EnergyPlus_Support] Re: design builder inter block partition

To: EnergyPlus_Support@xxxxxxxxxxxxxxx
Subject: Re: [EnergyPlus_Support] Re: design builder inter block partition
From: Linda Lawrie <linda@xxxxxxxxxxxxxx>
Date: Mon, 24 Jun 2013 06:49:44 -0600
Delivered-to: mailing list EnergyPlus_Support@xxxxxxxxxxxxxxx
Delivery-date: Mon, 24 Jun 2013 09:06:57 -0600
Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=yahoogroups.com; s=echoe; t=1372086416; bh=0wh0L4YQ5ex7QtnFHJaIny/O1cxq6OfxQxXi+b9tPFo=; h=Received:Received:X-Yahoo-Newman-Id:X-Sender:X-Apparently-To:X-Received:X-Received:X-Received:X-Received:X-Received:X-Received:X-Received:X-Mailer:To:In-Reply-To:References:X-Identified-User:X-Originating-IP:X-eGroups-Msg-Info:From:X-Yahoo-Profile:Sender:MIME-Version:Mailing-List:Delivered-To:List-Id:Precedence:List-Unsubscribe:Date:Subject:Reply-To:X-Yahoo-Newman-Property:Content-Type; b=4YjY5/cP10U0DaO+o5O2H7i4osiUnT6YnQMrBDo/NeCiZsfpLnIgT1PtZsNHHoWSfxlHC7BcQmiGJ/fwvVAfN8r+FPPjfp3u0I6bo0JslaFJsiRIQaV/Zm/KyxCAUaPy1RPvFE9RFPP52C94Fdq4nBOoTctIZFn60AspWfLMccc=
Domainkey-signature: a=rsa-sha1; q=dns; c=nofws; s=echoe; d=yahoogroups.com; b=DeN43G8RPcPHOYfYsxs/3GskV7+PHF39twYRO9QtB8KjGZFaVMnN6MsedSq9a6vhY9H1GnMh4yTwmlxFq2JCcOoXcdfbxtaSnj5wR41byB2yho3F6ms3Y/bQhRpPAfeOkUdx1S3beVutZXzs+NOKgzdD1q1hxpUQ53Lss3tYH30=;
Envelope-to: linda@xxxxxxxxxxxxxx
In-reply-to: <kq96dl+st9@eGroups.com>
List-id: <EnergyPlus_Support.yahoogroups.com>
List-unsubscribe: <mailto:EnergyPlus_Support-unsubscribe@yahoogroups.com>
Mailing-list: list EnergyPlus_Support@xxxxxxxxxxxxxxx; contact EnergyPlus_Support-owner@xxxxxxxxxxxxxxx
References: <kq96dl+st9@eGroups.com>
Reply-to: EnergyPlus_Support@xxxxxxxxxxxxxxx
Sender: EnergyPlus_Support@xxxxxxxxxxxxxxx

I am not sure what you mean -- suggest that you send your input file and detailed questions to the helpdesk.

Read the guidelines on posting questions to the helpdesk:
http://energyplus.helpserve.com/Troubleshooter/Step/View/4

I noticed that this is correct for the output surface temperature, but for the output -opaque surface inside face conduction- the simulation give me two diffent values, whether I insert one code or another.
Why?
Which one should I consider??

__._,_.___

Primary EnergyPlus support is found at: http://energyplus.helpserve.com or send a message to energyplus-support@xxxxxxxx The primary EnergyPlus web site is found at: http://www.energyplus.gov The group web site is: http://groups.yahoo.com/group/EnergyPlus_Support/ Attachments are currently allowed but be mindful that not everyone has a high speed connection. Limit attachments to small files. EnergyPlus Documentation is searchable. Open EPlusMainMenu.pdf under the Documentation link and press the "search" button.

Your email settings: Individual Email|Traditional
Change settings via the Web (Yahoo! ID required)
Change settings via email: Switch delivery to Daily Digest | Switch to Fully Featured
Visit Your Group | Yahoo! Groups Terms of Use | Unsubscribe

__,_._,___

References:
- [EnergyPlus_Support] Re: design builder inter block partition
  - From: elisa88.ribi

Prev by Date: [EnergyPlus_Support] web-based documentation resource for EnergyPlus
Next by Date: [EnergyPlus_Support] heat flux
Previous by thread: [EnergyPlus_Support] Re: design builder inter block partition
Next by thread: [EnergyPlus_Support] Heating Load = Zero?
Index(es):
- Date
- Thread