[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[EnergyPlus_Support] two sets of connectorLists in a single loop
- To: <EnergyPlus_Support@xxxxxxxxxxxxxxx>
- Subject: [EnergyPlus_Support] two sets of connectorLists in a single loop
- From: <adrianchong85@xxxxxxxxx>
- Date: 15 Dec 2013 16:35:27 -0800
- Delivered-to: mailing list EnergyPlus_Support@xxxxxxxxxxxxxxx
- Delivery-date: Sun, 15 Dec 2013 17:35:32 -0700
- Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=yahoogroups.com; s=echoe; t=1387154129; bh=hN/+FlJB7N+C2Llyhs6wpnPKqoTSPpiD5aB/XbEBIrU=; h=Received:Received:X-Yahoo-Newman-Id:X-Sender:X-Apparently-To:X-Received:X-Received:X-Received:X-Received:X-Received:X-Received:X-Received:To:Message-ID:X-Mailer:X-Originating-IP:X-eGroups-Msg-Info:X-Yahoo-Post-IP:From:X-Yahoo-Profile:Sender:MIME-Version:Mailing-List:Delivered-To:List-Id:Precedence:List-Unsubscribe:Date:Subject:Reply-To:X-Yahoo-Newman-Property:Content-Type; b=y3Q/XezhlfZVIlhVWPQesmbUgCMj/f9J+ETdl52gZFQT1TFm31nzUPdlFtlHucTOPcGiuol5QK4lqQDBraxrtskH3MNblSn9g5fqg4wD/3GN/zoizUFZoXCIfntU6B3cwtC4OBBOZjs9Oxdb7REVijWfcVFRqC2Ip3mJvxPO8rs=
- Domainkey-signature: a=rsa-sha1; q=dns; c=nofws; s=echoe; d=yahoogroups.com; b=wvFVXl531/j4FaHlTen3ge2lHKwummaA0x8VLg9xgYdGJ4E1jOembiVsZX/IMGa5e4zxKrm7vrIeqDo+b4zl13juSGGw0jf5gK0w400cc+yYB4cwSckEeF0FSyGx4GV4isRvD+0/OXBUSaZihQI1hYJOZzUcDHSNnEpiV8KtByg=;
- Envelope-to: linda@xxxxxxxxxxxxxx
- List-id: <EnergyPlus_Support.yahoogroups.com>
- List-unsubscribe: <mailto:EnergyPlus_Support-unsubscribe@yahoogroups.com>
- Mailing-list: list EnergyPlus_Support@xxxxxxxxxxxxxxx; contact EnergyPlus_Support-owner@xxxxxxxxxxxxxxx
- Reply-to: EnergyPlus_Support@xxxxxxxxxxxxxxx
- Sender: EnergyPlus_Support@xxxxxxxxxxxxxxx
Dear EnergyPlus Users,
I am trying to model the following plant loop in EnergyPlus
2 chillers in parallel connected to 2 pumps in parallel
----- -- chiller1-- ----- --pump1-- ---------
\ chiller2 / \ pump2 /
Howerver EnergyPlus only allows the use of a single set of splitter and mixer in each loop (do correct me if I'm wrong).
Hence I would like to seek advice on some of the methods/best practices that has been taken to work around this (alternative to modeling 2 pumps in parallel).
Thank you and I would greatly appreciate any inputs
Regards,
Adrian
__._,_.___
Primary EnergyPlus support is found at:
http://energyplus.helpserve.com or send a message to energyplus-support@xxxxxxxx
The primary EnergyPlus web site is found at:
http://www.energyplus.gov
The group web site is:
http://groups.yahoo.com/group/EnergyPlus_Support/
Attachments are currently allowed but be mindful that not everyone has a high speed connection. Limit attachments to small files.
EnergyPlus Documentation is searchable. Open EPlusMainMenu.pdf under the Documentation link and press the "search" button.
![]()
__,_._,___