[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [EnergyPlus_Support] HVAC BESTTEST





Linda,
You are right. I got the results although there was a severe error.
Thank you very much.
Wenting

2014-10-17 23:21 GMT+09:00 Linda Lawrie linda@xxxxxxxxxxxxxx [EnergyPlus_Support] <EnergyPlus_Support@xxxxxxxxxxxxxxx>:
 

Note that it gives you a severe error but goes ahead and completes successfully.

As versions change, so do error/warning messages.

Linda

At 11:13 PM 10/16/2014, Wenting Ding dingwenting@xxxxxxxxx [EnergyPlus_Support] wrote:


Linda,
Ã?
The following is theÃ? full error messages. For your reference, I attached the idf file also(original and updated version). Thank you.
Ã?
Ã?
Program Version,EnergyPlus-Windows-64 8.1.0.009, YMD=2014.10.17 10:12,IDD_Version 8.1.0.009
� �  ** Warning ** Timestep: Requested number (1) is less than the suggested minimum of 4.
� �  **� �  ~~~� �  ** Please see entry for Timestep in Input/Output Reference for discussion of considerations.
� �  ** Warning ** Weather file location will be used rather than entered (IDF) Location object.
� �  **� �  ~~~� �  ** ..Location object=UNKNOWN
� �  **� �  ~~~� �  ** ..Weather File Location=Miami/Int'l Airport FL USA TMY--12839 WMO#=722020
� �  **� �  ~~~� �  ** ..due to location differences, Latitude difference=[2.00E-002] degrees, Longitude difference=[2.00E-002] degrees.
� �  **� �  ~~~� �  ** ..Time Zone difference=[0.0] hour(s), Elevation difference=[100.00] percent, [2.00] meters.
� �  ** Severe�  ** This building has no thermal mass which can cause an unstable solution.
� �  **� �  ~~~� �  ** Use Material object for all opaque material definitions except very light insulation layers.
� �  ** Warning ** The Standard Ratings is calculated for Coil:Cooling:DX:SingleSpeed = ZONE1WINDACDXCOIL but not at the AHRI test condition due to curve out of bound.
� �  **� �  ~~~� �  **�  Review the Standard Ratings calculations in the Engineering Reference for this coil type. Also, use Output:Diagnostics, DisplayExtraWarnings for further guidance.
� �  ************* Testing Individual Branch Integrity
� �  ************* All Branches passed integrity testing
� �  ************* Testing Individual Supply Air Path Integrity
� �  ************* All Supply Air Paths passed integrity testing
� �  ************* Testing Individual Return Air Path Integrity
� �  ************* All Return Air Paths passed integrity testing
� �  ************* No node connection errors were found.
� �  ************* Beginning Simulation
� �  ************* Simulation Error Summary *************
� �  ************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.
� �  ************* EnergyPlus Sizing Error Summary. During Sizing: 0 Warning; 0 Severe Errors.
� �  ************* EnergyPlus Completed Successfully-- 3 Warning; 1 Severe Errors; Elapsed Time=00hr 00min�  0.97sec


2014-10-17 10:21 GMT+09:00 Linda Lawrie linda@xxxxxxxxxxxxxx [EnergyPlus_Support] < EnergyPlus_Support@xxxxxxxxxxxxxxx>:
� 

That doesn't look like a severe error -- why not paste in the full .err
file?


On 2014-10-16 19:19, dingwenting@xxxxxxxxx [EnergyPlus_Support] wrote:
> Hi,
>
> I got the CE100.idf from others and it was the old version. I updated
> it to version 8.1 and ran it. but got a severe error.
>
> MATERIAL:Regular-R,
> INSULATION-EXT, ! Material Name
> VerySmooth, ! Roughness
> 50.00 , ! Thermal Resistance {m2-K/W}
> 0.9000 , ! Thermal Absorptance
> 0.1000 , ! Solar Absorptance
> 0.1000 ; ! Visible Absorptance
>
> MATERIAL:Regular-R,
> INSULATION-INT, ! Material Name
> VerySmooth, ! Roughness
> 50.00 , ! Thermal Resistance {m2-K/W}
> 0.9000 , ! Thermal Absorptance
> 0.6000 , ! Solar Absorptance
> 0.6000 ; ! Visible Absorptance
>
> CONSTRUCTION,
> LTWALL, ! Construction Name
> ! Material layer names follow:
> INSULATION-EXT,
> INSULATION-INT;
>
> The error message is
>
> This building has no thermal mass which can cause an unstable
> solution.
> ** ~~~ ** Use Material object for all opaque material definitions
> except very light insulation layers.
>
> In Case E100 the wall construction is conposed of only two insulation
> layers.
>
> Who can give me some advice?
>
> Thank you very much.
>
>
>
> Links:
> ------
> [1] http://energyplus.helpserve.com
> [2] http://www.energyplus.gov
> [3] http://groups.yahoo.com/group/EnergyPlus_Support/
> [4]
> https://groups.yahoo.com/neo/groups/EnergyPlus_Support/info;_ylc=X3oDMTJlcjZwNDY5BF9TAzk3MzU5NzE0BGdycElkAzMzODc0ODgEZ3Jwc3BJZAMxNzA1MDA3Mzg5BHNlYwN2dGwEc2xrA3ZnaHAEc3RpbWUDMTQxMzUwODc1NA --
> [5]
> https://groups.yahoo.com/neo/groups/EnergyPlus_Support/members/all;_ylc=X3oDMTJmMGU2NzlqBF9TAzk3MzU5NzE0BGdycElkAzMzODc0ODgEZ3Jwc3BJZAMxNzA1MDA3Mzg5BHNlYwN2dGwEc2xrA3ZtYnJzBHN0aW1lAzE0MTM1MDg3NTQ-
> [6]
> https://groups.yahoo.com/neo;_ylc=X3oDMTJkOXV2bnZ0BF9TAzk3NDc2NTkwBGdycElkAzMzODc0ODgEZ3Jwc3BJZAMxNzA1MDA3Mzg5BHNlYwNmdHIEc2xrA2dmcARzdGltZQMxNDEzNTA4NzU0
> [7] https://info.yahoo.com/privacy/us/yahoo/groups/details.html
> [8] https://info.yahoo.com/legal/us/yahoo/utos/terms/





Content-Type: application/octet-stream; name="CASEE100T.IDF"
Content-Disposition: attachment; filename="CASEE100T.IDF"
X-Attachment-Id: f_i1d2x0s40

Content-Type: application/octet-stream; name="CASEE100.IDF"
Content-Disposition: attachment; filename="CASEE100.IDF"
X-Attachment-Id: f_i1d2z5x81




__._,_.___

Posted by: Wenting Ding <dingwenting@xxxxxxxxx>


Primary EnergyPlus support is found at:
http://energyplus.helpserve.com or send a message to energyplus-support@xxxxxxxx

The primary EnergyPlus web site is found at:
http://www.energyplus.gov

The group web site is:
http://groups.yahoo.com/group/EnergyPlus_Support/

Attachments are currently allowed but be mindful that not everyone has a high speed connection.  Limit attachments to small files.

EnergyPlus Documentation is searchable.  Open EPlusMainMenu.pdf under the Documentation link and press the "search" button.




Visit Your Group
Yahoo! Groups
PrivacyUnsubscribeTerms of Use

__,_._,___