[Equest-users] Combining Parametric Components

Jeremy McClanathan jmcclanathan at CDiengineers.com
Mon Jun 1 15:32:06 PDT 2009


Thank you very much for your help!  However, I don't believe I explained my question well enough.  In my model, I currently have 13 envelope measures I have analyzed by creating 13 individual parametric components that are assigned to 13 individual parametric runs.  When I analyzed them, I compared each measure to either the baseline or a previous measure as appropriate.  Now, I am finished analyzing envelope measures and I would like to analyze about 10 HVAC measures.  I would like to keep my original baseline, but I also want to analyze the HVAC measures assuming that the envelope measures will be incorporated into the building.  So, I would like to combine the 13 envelope components into 1 envelope run, rather than 13 individual runs.  Then, I will compare HVAC measures to either the new baseline envelope run or previous HVAC measures as appropriate.

For example, I currently have the following configuration:

Envelope Run-1
  Envelope Component-1
Envelope Run-2
  Envelope Component-2
Envelope Run-13
  Envelope Component-13


And I would to have to have the following configuration:

All Envelope Runs-1
  Envelope Component-1
  Envelope Component-2
  Envelope Component-13
HVAC Run-1
        HVAC Component-1
HVAC Run-2
        HVAC Component-2
HVAC Run-13
        HVAC Component-13

Is it possible to combine the envelope components I have already created into 1 envelope run, or do I need to recreate all of the envelope components in order to accomplish this?

Thank you for your help!

Jeremy




-----Original Message-----
From: Vikram Sami [mailto:VSami at lasarchitect.com]
Sent: Monday, June 01, 2009 2:27 PM
To: John Aulbach; Jeremy McClanathan; equest-users at lists.onebuilding.org
Subject: RE: [Equest-users] Combining Parametric Components

Actually when you run parametrics cumulatively I believe they do take the properties of the previous run into account. So for example if run#6 makes your glass darker and run#7 adds daylight sensors, run#7 will assume the darker glass.

Vikram Sami, LEED AP
Direct Phone 404-253-1466 | Direct Fax 404-253-1366
LORD, AECK & SARGENT ARCHITECTURE
1201 Peachtree Street NE, Suite 300, Atlanta, GA 30361
Responsive Design • Technological Expertise • Exceptional Service
Please visit our new website | www.lordaecksargent.com
??Think GREEN before you print.


-----Original Message-----
From: John Aulbach [mailto:jra_sac at yahoo.com]
Sent: Monday, June 01, 2009 5:21 PM
To: Jeremy McClanathan; equest-users at lists.onebuilding.org; Vikram Sami
Subject: Re: [Equest-users] Combining Parametric Components


Jeremy, What Vikram says is correct. However, I believe you STILL need to add all of the Parametric components into one run to compare to the Base. Run #7 will compare to Run #6, but Run #7 won't have Run #6 parameters in it, as well as its own.

In other words, the parameters will not accumulate as the run numbers get bigger. I believe you still need a cumulative run will all envelope parameters added into that run.

John Aulbach

--- On Mon, 6/1/09, Vikram Sami <VSami at lasarchitect.com> wrote:

> From: Vikram Sami <VSami at lasarchitect.com>
> Subject: Re: [Equest-users] Combining Parametric Components
> To: "Jeremy McClanathan" <jmcclanathan at CDiengineers.com>, equest-users at lists.onebuilding.org
> Date: Monday, June 1, 2009, 2:09 PM
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
> You can
> run the parametric runs
> incrementally or cumulatively.  To run them
> cumulatively, in the parametric
> run dialogue, you need to base the run on the previous run
> (you can base the un
> on any parametric run preceding it).
>
>
>
>
>
>
> Vikram
> Sami, LEED AP
>
> Direct
> Phone 404-253-1466 | Direct Fax 404-253-1366
>
> LORD, AECK & SARGENT ARCHITECTURE
>
> 1201 Peachtree Street NE, Suite 300,
> Atlanta, GA 30361
>
> Responsive
> Design · Technological Expertise · Exceptional
> Service
>
> Please
> visit our new website | www.lordaecksargent.com
>
> P
> Think
> GREEN before you print.
>
>
>
>
>
>
>
>
>
>
>
>
> From: equest-users-bounces at lists.onebuilding.org
> [mailto:equest-users-bounces at lists.onebuilding.org] On
> Behalf Of Jeremy
> McClanathan
>
> Sent: Monday, June 01, 2009 4:57 PM
>
> To: equest-users at lists.onebuilding.org
>
> Subject: [Equest-users] Combining Parametric
> Components
>
>
>
>
>
>
>
> Hello,
>
>
>
> Does anyone out there know whether or
> not it is possible to
> take parametric components that are currently each being
> used for individual
> parametric runs and combine all of them under 1 parametric
> run?
>
>
>
> Currently, I have a model where I have
> analyzed 13 envelope
> measures using parametric runs.  Now, I would like
> combine all of them
> into 1 run called envelope measures.  Is this
> possible?
>
>
>
> Jeremy
>
>
>
> This email message, including
> any attachments, is for the sole use of the intended
> recipient and may contain
> confidential, proprietary, and/or privileged information,
> as well as content
> subject to copyright and other intellectual laws.  If
> you are not the
> intended recipient, you may not disclose, use, copy, or
> distribute the email
> message or its attachments.  If you believe you have
> received this email
> message in error, please contact the sender by reply email,
> immediately delete
> this email and destroy copies.
>
>
>
>
>
>
>
> -----Inline Attachment Follows-----
>
> _______________________________________________
> Equest-users mailing list
> http://lists.onebuilding.org/listinfo.cgi/equest-users-onebuilding.org
> To unsubscribe from this mailing list send  a blank
> message to EQUEST-USERS-UNSUBSCRIBE at ONEBUILDING.ORG
>





This email message, including any attachments, is for the sole use of the intended recipient and may contain confidential, proprietary, and/or privileged information, as well as content subject to copyright and other intellectual laws. If you are not the intended recipient, you may not disclose, use, copy, or distribute the email message or its attachments. If you believe you have received this email message in error, please contact the sender by reply email, immediately delete this email and destroy copies.



More information about the Equest-users mailing list