[Equest-users] Unmet Hours

[Dakota Kelley]

…the way the hours are counted.  The Air-Side Summary report is good for showing heating vs. cooling hours, and which zones are problematic, but it counts hours simultaneously and yields an inflated number.   Multiply the percentage in the BEPS report by the number of hours the fans are on and you’ll have the number you’re looking for.  To split that total between heating and cooling, I apply the same ratio shown in the Air-Side Summary report.  There’s probably a more accurate way to do it, but another user will have to enlighten all of us...

 

 

  
                                

DAKOTA KELLEY 

Project Designer | Energy Analyst

                          

                              Office: 214.744.6199                 

                              Cell: 214.280.3825

                              Fax: 214.744.0770    

 

http://www.teliospc.com <http://www.teliospc.com/>          3535 Travis St. Suite 115

dakotak at teliospc.com            Dallas, TX 75204                                                     

                                

| MEP ENGINEERING · ENERGY MODELING · LEED CONSULTATION · COMMISSIONING |

 

CONFIDENTIALITY NOTICE: This email is intended only for the use of the individual or entity to which it is addressed, 

And may contain information that is privileged, confidential and exempt from disclosure under applicable law. If you

are not the intended recipient, please email the sender immediately, and delete this email from all computers.  Any 

distribution or other use is strictly prohibited.  Copyright © 2009 Telios Corporation.

 

 

 

  

 

From: Martz, Amanda [mailto:amartz at klingstubbins.com] 
Sent: Thursday, July 15, 2010 3:22 PM
To: Kelsey VanTassel; M. Shields; equest-users at lists.onebuilding.org
Subject: Re: [Equest-users] Unmet Hours

 

When I look under the summary tab, it says I have 34% unmet hours. When I look at the BEPS report, it says I have 3%. Does anyone know what the difference in these numbers is?

 

________________________________

From: equest-users-bounces at lists.onebuilding.org [mailto:equest-users-bounces at lists.onebuilding.org] On Behalf Of Kelsey VanTassel
Sent: Thursday, July 15, 2010 3:50 PM
To: M. Shields; equest-users at lists.onebuilding.org
Subject: Re: [Equest-users] Unmet Hours

 

I like to look under Airside HVAC. Click on the summary tab, then click on “project” in the component tree on the left hand side. It will show you the sum automatically.

 

Kelsey Van Tassel

Mechanical Engineer | kvantassel at sustaineng.com

608.836.4488 ext. 20 | Fax: 608.836.4477

 

Sustainable Engineering Group

901 Deming Way, Suite 201

Madison, WI 53717

www.sustaineng.com <http://www.sustaineng.com/> 

 

 

From: equest-users-bounces at lists.onebuilding.org [mailto:equest-users-bounces at lists.onebuilding.org] On Behalf Of M. Shields
Sent: Thursday, July 15, 2010 2:47 PM
To: equest-users at lists.onebuilding.org
Subject: [Equest-users] Unmet Hours

 

Hi All,

 

I am trying to determine the number of unmet cooling and heating hours for my model.  From what I’ve read on the BEPU/BEPS reports I can find the % of the hours that the load is unmet, but is there a way to break this out into cooling and heating time?  The other alternative I see is to go through either the SS-F reports, or the Air-Side HVAC section and add up all of the zones unmet heating and cooling hours.  Does anyone know of a better way to determine this?

 

Thanks,

Michael Shields

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/equest-users-onebuilding.org/attachments/20100715/aab32c0e/attachment-0001.htm>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: image/png
Size: 3170 bytes
Desc: image001.png
URL: <http://lists.onebuilding.org/pipermail/equest-users-onebuilding.org/attachments/20100715/aab32c0e/attachment-0001.png>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: image/jpeg
Size: 2143 bytes
Desc: image002.jpg
URL: <http://lists.onebuilding.org/pipermail/equest-users-onebuilding.org/attachments/20100715/aab32c0e/attachment-0001.jpeg>