[Equest-users] Different roof and floor.

[Jeremy McClanathan]

Another option is to save your model with a diff name, go into the wizard of your new model and create two zones, one for the area below the second shell and one more for the surrounding area.  Set the HVAC system to create a system per zone so the program will automatically create two plenums and associated roofs.  Set mode to detailed, copy the two plenum zones, spaces (and associated walls and roofs), and polygons from the new model and replace the plenum in your original model with the new plenums once the original model is in the detailed edit mode.  Then, delete the roof of the plenum under the second shell.

This only works if your original model has plenums, and only one plenum per floor.  If you have a simple shape or only a few zones, this may be over-kill.  But, if your footprint has a lot of vertices or you have a lot of zones that would otherwise need to be broken up, this method may be a time saver.

Jeremy

From: Charles Land [mailto:cland at geo-marine.com]
Sent: Friday, October 29, 2010 6:19 AM
To: Bruce Easterbrook; Самолётов Михаил
Cc: equest-users at lists.onebuilding.org
Subject: Re: [Equest-users] Different roof and floor.

I always use the roof and floor designation in the wizard of below conditioned space and over conditioned space.  And then any area that is not directly under the second floor I make it a separate shell with the appropriate roof.  I suppose either method would work, but if you have a lot of spaces it could become tedious having to go through the construction of each one individually.

From: equest-users-bounces at lists.onebuilding.org [mailto:equest-users-bounces at lists.onebuilding.org] On Behalf Of Bruce Easterbrook
Sent: Friday, October 29, 2010 9:14 AM
To: Самолётов Михаил
Cc: equest-users at lists.onebuilding.org
Subject: Re: [Equest-users] Different roof and floor.


  One way is to make the zoning on the first floor line up with the second floor foot print.  This I think, is the best way if the second floor is a complex shape.  The addition of a roof or it's deletion can be geometrically tricky to do if it spans only part of a zone.  I have found lining up the zones with the foot print an easier solution.  You may have to add a few extra zones to get the matching shape.  You delete the roof under the foot print.  If the zoning doesn't match your HVAC zones you can adjust the zone grouping so that it does.  Turn any interior walls into air walls if they don't actually exist on the first floor.  You may also have to adjust or delete the floor of the second story as the ceiling of the first floor is floor of the second floor.  Check through your layers to make sure they are consistent with the actual construction.  Make sure your boundaries are referencing the proper adjacent zones.  This is the technique, and may not exactly match what you are doing, you will have to check through everything to make sure everything is consistent.
Bruce Easterbrook
Abode Engineering

On 29/10/2010 02:48 AM, Самолётов Михаил wrote:
Hi

I have 2-storey building. The 1st storey in a plan is not like the 2nd one. That's why I created 2 shells (one above the other). For the 1st storey I have created a roof (because part of a ceiling is outside the building). And for the 2nd storey I have created a floor. Parameters of the roof of 1st story and the floor of the 2nd story are different! During the calculation the eQUEST will calculate Heat Flux through the ceiling/floor.
How eQUST calculate it if ceiling of the 1st storey is not the same as the floor of the 2nd storey?
If air condition in 1st and 2nd story same, this question not so important, but if condition has big different - this question is very actual!


Sincerely yours,
Mikhail Samoletov
Chief engineer of
"Numerical Simulation Department"
TECHNIQUE BUREAU
Cvetochnaya str, 25"Zh", 196084 St.Petersburg, Russia
www.bt-comfort.ru<http://www.bt-comfort.ru>
phone/fax +7 (812) 318-50-30
mob. +7 (931) 244-83-77






_______________________________________________

Equest-users mailing list

http://lists.onebuilding.org/listinfo.cgi/equest-users-onebuilding.org

To unsubscribe from this mailing list send  a blank message to EQUEST-USERS-UNSUBSCRIBE at ONEBUILDING.ORG<mailto:EQUEST-USERS-UNSUBSCRIBE at ONEBUILDING.ORG>

This email message, including any attachments, is for the sole use of the intended recipient and may contain confidential, proprietary, and/or privileged information, as well as content subject to copyright and other intellectual laws.  If you are not the intended recipient, you may not disclose, use, copy, or distribute the email message or its attachments.  If you believe you have received this email message in error, please contact the sender by reply email, immediately delete this email and destroy copies.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/equest-users-onebuilding.org/attachments/20101029/af70f7d5/attachment-0001.htm>