RE: [EnergyPlus_Support] input for HAMT modeling outputs

Look at the EIO file. It reports important information on how the cells were automatically setup.

From: EnergyPlus_Support@xxxxxxxxxxxxxxx [mailto:EnergyPlus_Support@xxxxxxxxxxxxxxx] On Behalf Of ozgur gocer
Sent: Monday, February 01, 2010 11:13 AM
To: EnergyPlus_Support@xxxxxxxxxxxxxxx
Subject: RE: [EnergyPlus_Support] input for HAMT modeling outputs

thanks for your reply. In modeling wufi a grid is needed. but in Energyplus the input is only the thickness of layer. Then how can we specify the number of cell? If i specify for the output of RH, temperature or water content from 1 to let say 10 cells, does the program divide the construction (e.g a wall) into 10 cells?

best wishes

ozgur gocer

--- 01/02/10 Pzt tarihinde Edward G. Lyon <eglyon@xxxxxxx> şöyle yazıyor:

Kimden: Edward G. Lyon <eglyon@xxxxxxx>
Konu: RE: [EnergyPlus_Support] input for HAMT modeling outputs
Kime: "EnergyPlus_Support@yahoogroups.com" <EnergyPlus_Support@yahoogroups.com>
Tarihi: 1 Şubat 2010 Pazartesi, 16:28

The way WUFI calculates is to divide each material in a wall assembly into a number of sub layers (cells) and at each time step it calculates a heat and moisture balance of all the cells in the wall assembly. Apparently, EnergyPlus allows you to output the individual cell data which would allow you to look at a temperature/ moisture profile of the wall. You need RH and moisture content because 100% RH does not always mean the material is fully saturated. You may need to check the reference to find it, but there should be surface heat and moisture fluxes as well.

Ned Lyon, P.E. (MA)
Staff Consultant

SIMPSON GUMPERTZ & HEGER
781.907.9000 main
781.907.9350 direct
781.907.9009 fax
www.sgh.com

From: EnergyPlus_Support@ yahoogroups. com [mailto:EnergyPlus_ Support@yahoogro ups.com] On Behalf Of ozgur gocer
Sent: Saturday, January 30, 2010 4:50 PM
To: EnergyPlus_Support@ yahoogroups. com
Subject: [EnergyPlus_ Support] input for HAMT modeling outputs

Hi,

i looked at the example file for HAMT modeling. what is the meaning of outputs;

"HAMT-Profile Construction 1 cell 1 Temp"

"HAMT-Profile Construction 1 cell 1 water"

"HAMT-Profile Construction 1 cell 1 RH"

the another question; Is it possible to get the heat flux output data of a surface

with my best regards

ozgur

Yahoo! Türkiye açıldı!
Haber, Ekonomi, Videolar, Oyunlar hepsi Yahoo! Türkiye'de!
www.yahoo.com. tr

Yahoo! Türkiye açıldı!
Haber, Ekonomi, Videolar, Oyunlar hepsi Yahoo! Türkiye'de!
www.yahoo.com.tr

__._,_.___

The primary EnergyPlus web site is found at: http://www.energyplus.gov The group web site is: http://groups.yahoo.com/group/EnergyPlus_Support/ Attachments are currently allowed but be mindful that not everyone has a high speed connection. Limit attachments to small files. EnergyPlus Documentation is searchable. Open EPlusMainMenu.pdf under the Documentation link and press the "search" button.

Your email settings: Individual Email|Traditional
Change settings via the Web (Yahoo! ID required)
Change settings via email: Switch delivery to Daily Digest | Switch to Fully Featured
Visit Your Group | Yahoo! Groups Terms of Use | Unsubscribe

__,_._,___