Thanks�.it actually helps to readd and reread the documentation
most of the time. Sorry to bother everyone with the trivial�
Ned
Lyon, P.E. (MA)
Staff Consultant
SIMPSON
GUMPERTZ & HEGER
781.907.9000 main
781.907.9350 direct
781.907.9009 fax
www.sgh.com
From:
EnergyPlus_Support@xxxxxxxxxxxxxxx [mailto:EnergyPlus_Support@xxxxxxxxxxxxxxx] On
Behalf Of Bereket Nigusse
Sent: Friday, July 16, 2010 6:00 PM
To: EnergyPlus_Support@xxxxxxxxxxxxxxx
Subject: Re: [EnergyPlus_Support] EMS Actuator
Edward
You
might want to try "District HeatingPower Level” in place of
"Design Level {W}" for Actuated Component Control Type.
Bereket
From: Edward G. Lyon
<eglyon@xxxxxxx>
To: "EnergyPlus_Support@xxxxxxxxxxxxxxx"
<EnergyPlus_Support@xxxxxxxxxxxxxxx>
Sent: Fri, July 16, 2010 5:45:55 PM
Subject: RE: [EnergyPlus_Support] EMS Actuator
Unfortunately there are often legal
issues attached to sharing some of my files. I’ll see if I can recreate
the error with a dummy file and send that. The crash is related to the
EMS because the main file runs fine and the sensor I made does not crash the
run. Just adding the actuator without a program specified crashes the
run, so I suspect I am not specifying the right things to operate the steam.
Ned Lyon, P.E. (MA)
Staff Consultant
SIMPSON GUMPERTZ & HEGER
781.907.9000 main
781.907.9350 direct
781.907.9009 fax
www.sgh.com
From:
EnergyPlus_Support@ yahoogroups. com [mailto:EnergyPlus_ Support@yahoogro ups.com] On Behalf Of Linda
Lawrie
Sent: Friday, July 16, 2010 5:27 PM
To: EnergyPlus_Support@ yahoogroups. com
Subject: Re: [EnergyPlus_ Support] EMS Actuator
It might be more helpful if you sent the full input
file to the helpdesk: energyplus-support@ gard.com
At 03:23 PM 7/16/2010, Edward G. Lyon wrote:
I am trying to reset the watts on the following steam generator:
SteamEquipment,
Direct Water, !- Name
unconditioned, !- Zone Name
Always On, !- Schedule Name
EquipmentLevel, !- Design Level Calculation Method
50, !- Design Level {W}
, !- Watts per Zone Floor Area {W/m2}
, !- Watts per Person {W/Person}
1, !- Fraction Latent
, !- Fraction Radiant
, !- Fraction Lost
General; !- End-Use Subcategory
I assumed I could use an actuator:
EnergyManagementSys tem:Actuator,
MoistureGain, !- Name
Direct Water, !- Actuated Component Unique Name
SteamEquipment, !- Actuated Component Type
Design Level {W}; !- Actuated Component Control Type
But this causes a system crash, so I must not be doing this correctly. I also tried to manipulate the schedule and could not get the right values to avoid crashing. Can someone give me a little guidance?
__._,_.___
Primary EnergyPlus support is found at:
http://energyplus.helpserve.com or send a message to energyplus-support@xxxxxxxx
The primary EnergyPlus web site is found at:
http://www.energyplus.gov
The group web site is:
http://groups.yahoo.com/group/EnergyPlus_Support/
Attachments are currently allowed but be mindful that not everyone has a high speed connection. Limit attachments to small files.
EnergyPlus Documentation is searchable. Open EPlusMainMenu.pdf under the Documentation link and press the "search" button.
Change settings via the Web (Yahoo! ID required)
Change settings via email: Switch delivery to Daily Digest | Switch to Fully Featured
Visit Your Group | Yahoo! Groups Terms of Use | Unsubscribe
__,_._,___