[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [EnergyPlus_Support] Re: error temperature out of boundary
I would try increasing the zone infiltration to the point where zone
temps nearly track outdoor temp. Then when you can get the simulation to
run, start adding report variables (e.g., zone temps, surface temps,
etc.) to see what is happening and then gradually reduce the
infiltration until the problem starts to reveal itself.
On 10/3/2012 9:11 PM, JFCS wrote:
> got the same problem... solutions anyone?
>
> --- In EnergyPlus_Support@xxxxxxxxxxxxxxx, "andresdagm" <andresdagm@...> wrote:
>> good day,
>> i have simulated my building but it has a error, maybe a surface is too small, i dont how why i get this errocr.
>>
>> thank you to any help.
>> ** Severe ** Temperature (low) out of bounds [-105.04] for zone="PISO2:CIRCULACION1", for surface="PISO2:CIRCULACION1_ROOF_1_7_2"
>> ** ~~~ ** During Warmup & Sizing, Environment=SUMMER DESIGN DAY IN PANORAMA, at Simulation time=01/15 17:45 - 17:48
>> ** ~~~ ** Zone="PISO2:CIRCULACION1", Diagnostic Details:
>> ** ~~~ ** ...Internal Heat Gain [6.850] W/m2
>> ** ~~~ ** ...Infiltration/Ventilation [0.114] m3/s
>> ** ~~~ ** ...Mixing/Cross Mixing [0.000] m3/s
>> ** ~~~ ** ...Zone is not part of HVAC controlled system.
>>
>>
>> ** Severe ** Temperature (low) out of bounds [-105.04] for zone="PISO2:CIRCULACION1", for surface="PISO2:CIRCULACION1_ROOF_1_7_2"
>> ** ~~~ ** During Warmup & Sizing, Environment=SUMMER DESIGN DAY IN PANORAMA, at Simulation time=01/15 17:45 - 17:48
>> ** ~~~ ** Zone="PISO2:CIRCULACION1", Diagnostic Details:
>> ** ~~~ ** ...Internal Heat Gain [6.850] W/m2
>> ** ~~~ ** ...Infiltration/Ventilation [0.114] m3/s
>> ** ~~~ ** ...Mixing/Cross Mixing [0.000] m3/s
>> ** ~~~ ** ...Zone is not part of HVAC controlled system.
>> ** Fatal ** CalcHeatBalanceInsideSurf: Program terminates due to preceding conditions.
>> ...Summary of Errors that led to program termination:
>> ..... Reference severe error count=6
>> ..... Last severe error=Temperature (low) out of bounds [-105.04] for zone="PISO2:CIRCULACION1", for surface="PISO2:CIRCULACION1_ROOF_1_7_2"
>> ************* Warning: Node connection errors not checked - most system input has not been read (see previous warning).
>> ************* Fatal error -- final processing. Program exited before simulations began. See previous error messages.
>> ** Warning ** DXFOut: Could not triangulate surface="PISO1D:CAFETERIA_CEILING_1_0_12", type="Roof", check surface vertex order(entry)
>> ** ~~~ ** ...use Output:Diagnostics,DisplayExtraWarnings; to show more details on individual surfaces.
>>
>
>
>
> ------------------------------------
>
> Primary EnergyPlus support is found at:
> http://energyplus.helpserve.com or send a message to energyplus-support@xxxxxxxx
>
> The primary EnergyPlus web site is found at:
> http://www.energyplus.gov
>
> The group web site is:
> http://groups.yahoo.com/group/EnergyPlus_Support/
>
> Attachments are currently allowed but be mindful that not everyone has a high speed connection. Limit attachments to small files.
>
> EnergyPlus Documentation is searchable. Open EPlusMainMenu.pdf under the Documentation link and press the "search" button.
> Yahoo! Groups Links
>
>
>
>
--
Richard A. Raustad
Senior Research Engineer
Florida Solar Energy Center
University of Central Florida
1679 Clearlake Road
Cocoa, FL 32922-5703
Phone: (321) 638-1454
Fax: (321) 638-1439 or 1010
Visit our web site at: http://www.fsec.ucf.edu
UCF - From Promise to Prominence: Celebrating 40 Years
------------------------------------
Primary EnergyPlus support is found at:
http://energyplus.helpserve.com or send a message to energyplus-support@xxxxxxxx
The primary EnergyPlus web site is found at:
http://www.energyplus.gov
The group web site is:
http://groups.yahoo.com/group/EnergyPlus_Support/
Attachments are currently allowed but be mindful that not everyone has a high speed connection. Limit attachments to small files.
EnergyPlus Documentation is searchable. Open EPlusMainMenu.pdf under the Documentation link and press the "search" button.
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/EnergyPlus_Support/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/EnergyPlus_Support/join
(Yahoo! ID required)
<*> To change settings via email:
EnergyPlus_Support-digest@xxxxxxxxxxxxxxx
EnergyPlus_Support-fullfeatured@xxxxxxxxxxxxxxx
<*> To unsubscribe from this group, send an email to:
EnergyPlus_Support-unsubscribe@xxxxxxxxxxxxxxx
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/