Hmm... could you send me a screenshot of the post-process tab? If readvars didn't run, there must be something wrong with the command-line in the first section...
Cheers,
Yi
Sent: 13 December 2012 17:19
To: EnergyPlus_Support@xxxxxxxxxxxxxxx
Subject: Re: [EnergyPlus_Support] jEPlus: manual post process
I seems that the manual post-processing option does not write anything to both the err and log files. I cleared the content of the log and err files, and the I run the manual post process. What I found is that both the err and log files are still blank, so are the results files. Only the main screen reports something (see below), but it is way too fast to read 30 eso files. Furthermore, when I search the file activities on the result folders, no files has been updated. I presume that the readvars.audit files in the result folders will have a newer timestamp. It seems that the manual post processing does nothing?
Thanks,
Ery
*************************************
Validating jobs. Hang on ...
Validation successful!
Jobs are compiled from 1 models and 1 weather files, with the following
Parameter Chains:
P1("@@LOCKOUT@@") --> P2("@@MAXDB@@") --> 30 jobs
30 jobs have been identified in total.
Simulation work directories and results will be stored in: /home/eryd/jEPlus/economizer/output/
13 Dec 2012 10:06:38 MST [Post-processor] Started ...
13 Dec 2012 10:06:38 MST [Post-processor] Writing results to /home/eryd/jEPlus/economizer/processed_results.csv
13 Dec 2012 10:06:38 MST [Post-processor] Writing stats to /home/eryd/jEPlus/economizer/my-mean.csv
13 Dec 2012 10:06:38 MST [Post-processor] Writing stats to /home/eryd/jEPlus/economizer/my-variance.csv
13 Dec 2012 10:06:38 MST [Post-processor] Writing stats to /home/eryd/jEPlus/economizer/my-min.csv
13 Dec 2012 10:06:38 MST [Post-processor] Writing stats to /home/eryd/jEPlus/economizer/my-max.csv
13 Dec 2012 10:06:38 MST [Post-processor] Done!
*************************************
On 12/13/2012 02:46 AM, Yi Zhang wrote:
Dear Ery,
This is more likely to be cauesed by an error in the program. Could you send me the jeplus.err file in the jEPlus folder? You can normally see the output log for readvarseso in jeplus.log file. Both of these log are accessible in the jEPlus GUI, in the "Tools" menu.
Cheers,
Yi
From: EnergyPlus_Support@xxxxxxxxxxxxxxx [EnergyPlus_Support@xxxxxxxxxxxxxxx] on behalf of Ery Djunaedy [ery.mailinglist@xxxxxxxxx]
Sent: 11 December 2012 20:30
To: EnergyPlus_Support@xxxxxxxxxxxxxxx
Subject: [EnergyPlus_Support] jEPlus: manual post process
Folks,
I am trying to extract another set of results from all my parametric
runs using the manual post process. I have specified the new MVI file,
but the result files are empty. Are we supposed to copy the new MVI file
to each of the parametric folders? Is there a way that we can output the
log for the readvareso to see where it fails?
Thanks,
Ery
__._,_.___
Primary EnergyPlus support is found at:
http://energyplus.helpserve.com or send a message to energyplus-support@xxxxxxxx
The primary EnergyPlus web site is found at:
http://www.energyplus.gov
The group web site is:
http://groups.yahoo.com/group/EnergyPlus_Support/
Attachments are currently allowed but be mindful that not everyone has a high speed connection. Limit attachments to small files.
EnergyPlus Documentation is searchable. Open EPlusMainMenu.pdf under the Documentation link and press the "search" button.
Change settings via the Web (Yahoo! ID required)
Change settings via email: Switch delivery to Daily Digest | Switch to Fully Featured
Visit Your Group | Yahoo! Groups Terms of Use | Unsubscribe
__,_._,___