It is simple, if you know how to run EPlus without a DesignBuilder interface.
Dr. Li
To: EnergyPlus_Support@xxxxxxxxxxxxxxx
From: jeremiah@xxxxxxxxxxxxxxxxxxxxxx
Date: Thu, 12 Apr 2012 10:49:52 -0700
Subject: Re: [EnergyPlus_Support] Re: old version
Simple:
Finish all tasks in whatever version of design builder, then export IDF, use transition version and work the file in IDF editor for latest version of E+, no you can not go back to design builder afterword, but that should not be needed.
Jeremiah D. Crossett
CleanTech Analytics
503-688-8951
This document may contain valuable information proprietary to CleanTech Analytics which is private and confidential. It may not be shared, copied, stored or transmitted in any form without the prior written consent of CleanTech Analytics
On Thu, Apr 12, 2012 at 10:35 AM, YuanLu Li <yli006@xxxxxxxxxxx> wrote:
Hi, Linda
I think the user's problem is not just the transition from Ver 6.0 to ver 7.0. He is using DesignBuilder. I believe, DesignBuidier cannot import IDF file. So, even if the version 7.0 is available, it cannot be loaded back into DesignBulder.
He has to find out what is the version of IDF needed for his DesignBuilder. If the version 6.0 is used, then he should stay with version 6.0, until his DesignBuilder is upgrated.
If he want to use version 7.0 with EPlus download directly, then we can help him.
> > Hello everybody!> > ** ~~~ ** Version in IDF="6.0.0.023" not the same asexpected="7.0.0"
> > With DesignBuilder I created a .idf file version 6.0.0.023. I want to
> > develop it in EnergyPlus (mainly to model pv and solar thermal). Online I
> > found the version 7.0.0.036 of EnergyPlus.
> > During the simulation in EnergyPlus I got the following error:
> >
> > ** Severe ** IP: Possible incorrect IDD File
> > ** ~~~ ** IDD Version:"IDD_Version 7.0.0.036"
> > ** ~~~ ** Possible Invalid Numerics or other problems
> > ** Fatal ** IP: Errors occurred on processing IDF file. Preceding
> > condition(s) cause termination.
> >
If he has version 7.0 loaded, the error message clearly showed that he has a version mismatch. May be the version 7.0 was not installed probably.
If his DesignBuiding is running version 6.0, why must he use version 7.0. Simulate within DsignBuilder using version 6.0, unless pv and solarthermal are not available from within DesignBuilder.
I offered to convert from version 4.0 to version 7.0 for one user, but the file was never posted. With the new conveter all the inter version files are avilable after the conversion.
Dr. Li
To: EnergyPlus_Support@xxxxxxxxxxxxxxx
From: linda@xxxxxxxxxxxxxx
Date: Thu, 12 Apr 2012 11:00:15 -0600
Subject: Re: [EnergyPlus_Support] Re: old version
The transition program from V6 to V7 in the EnergyPlus V7 install is solid.
It's certainly easy to try if you can't get a V7 IDF from Design Builder.
At 10:49 AM 4/12/2012, FrancescoP wrote:
------------------------------------Thank you Javed Iqbal.
I'm using Design Builder V3.0.0.064 but I am not able to get an Energy Plus Version 7 IDF file. Did you maybe forget a link? :-)
I think getting directly from DesignBuilder a Version 7 IDF file would be more sure than using the transition auxiliary program (I mean the conversion errors should be less probable), isn't it?
Best Regards
Francesco Passerini
--- In EnergyPlus_Support@xxxxxxxxxxxxxxx, Javed Iqbal <eee.javed@...> wrote:
>
> You can upgrade your file into higher version by Auxiliary program comes
> with Eplus. Check Auxiliary Program Help file section *"Using Older Version
> Input Files - Transition*" at page number 118.
>
> P.s If you are using Design Builder V3 you can directly get Energy Plus
> Version 7 IDF file. Check this
>
> [image: Inline image 1]
>
> Thanks
>
> On Thu, Apr 12, 2012 at 3:29 AM, FrancescoP <direzionecontraria@...>wrote:
>
> > **
> >
> >
> > Hello everybody!
> > With DesignBuilder I created a .idf file version 6.0.0.023. I want to
> > develop it in EnergyPlus (mainly to model pv and solar thermal). Online I
> > found the version 7.0.0.036 of EnergyPlus.
> > During the simulation in EnergyPlus I got the following error:
> >
> > ** Severe ** IP: Possible incorrect IDD File
> > ** ~~~ ** IDD Version:"IDD_Version 7.0.0.036"
> > ** ~~~ ** Version in IDF="6.0.0.023" not the same as expected="7.0.0"
> > ** ~~~ ** Possible Invalid Numerics or other problems
> > ** Fatal ** IP: Errors occurred on processing IDF file. Preceding
> > condition(s) cause termination.
> >
> > Actually, I got also other errors (because of AdaptiveConvectionAlgorithm
> > and probably because I didn't complete the model of the plants). However, I
> > wonder whether downloading the version 6.0.0.023 of EnergyPlus is possible,
> > please. I think it would be the best solution, wouldn't it?
> > Best Regards
> > Francesco Passerini
> >
> >
> >
>
>
>
> --
>
>
> Javed Iqbal, LEED AP, CEA
> Energy Analyst
>
Primary EnergyPlus support is found at:
http://energyplus.helpserve.com or send a message to energyplus-support@xxxxxxxx
The primary EnergyPlus web site is found at:
http://www.energyplus.gov
The group web site is:
http://groups.yahoo.com/group/EnergyPlus_Support/
Attachments are currently allowed but be mindful that not everyone has a high speed connection. Limit attachments to small files.
EnergyPlus Documentation is searchable. Open EPlusMainMenu.pdf under the Documentation link and press the "search" button.Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/EnergyPlus_Support/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/EnergyPlus_Support/join
(Yahoo! ID required)
<*> To change settings via email:
EnergyPlus_Support-digest@xxxxxxxxxxxxxxx
EnergyPlus_Support-fullfeatured@xxxxxxxxxxxxxxx
<*> To unsubscribe from this group, send an email to:
EnergyPlus_Support-unsubscribe@xxxxxxxxxxxxxxx
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
__._,_.___
Primary EnergyPlus support is found at:
http://energyplus.helpserve.com or send a message to energyplus-support@xxxxxxxx
The primary EnergyPlus web site is found at:
http://www.energyplus.gov
The group web site is:
http://groups.yahoo.com/group/EnergyPlus_Support/
Attachments are currently allowed but be mindful that not everyone has a high speed connection. Limit attachments to small files.
EnergyPlus Documentation is searchable. Open EPlusMainMenu.pdf under the Documentation link and press the "search" button.
Your email settings: Individual Email|Traditional
Change settings via the Web (Yahoo! ID required)
Change settings via email: Switch delivery to Daily Digest | Switch to Fully Featured
Visit Your Group | Yahoo! Groups Terms of Use | Unsubscribe
Change settings via the Web (Yahoo! ID required)
Change settings via email: Switch delivery to Daily Digest | Switch to Fully Featured
Visit Your Group | Yahoo! Groups Terms of Use | Unsubscribe
__,_._,___