RE: [EnergyPlus_Support] infiltration

Very good question. The infiltration value that you have was calculated from a test (blower door)???? If this its true, you can model one thermal zone for all the building. You will have an infiltration value for each wall and after you can use it for the ariflownetwork.

To: EnergyPlus_Support@xxxxxxxxxxxxxxx
From: maki_to_fai@xxxxxxxxx
Date: Tue, 5 Jun 2012 13:23:12 +0100
Subject: Re: [EnergyPlus_Support] infiltration

Hi Oscar,

I will use the design infiltration option but my question is :

how am I going to apply this value to the building?

I have 5 thermal zones all with windows attached. I know that 133m3/h refers to the whole building.

Do I have to break (or divide) this 133 m3/h value for each zone ( n=q/v by getting the 5 zone volumes , for example V1= 50m2, n =133/50 ...etc )

thank you

From: oscar hernandez <oscarhernandez_81@xxxxxxxxxxx>
To: energyplus_support@xxxxxxxxxxxxxxx
Sent: Tuesday, 5 June 2012, 11:06
Subject: RE: [EnergyPlus_Support] infiltration

Hi Teo,

The infiltrations values on a building depend on orientation (wind direction). If you have a value of 133 m³/h, for me, the best solution it's to simulate the buliding only with this value of infiltration (design infiltration), after you are going to have the infiltration value per wall (N, S, E ,W) with this you can calculate an infiltration surface for the airflownetwork.

Let me know if you need help!

Oscar.

To: EnergyPlus_Support@xxxxxxxxxxxxxxx
From: maki_to_fai@xxxxxxxxx
Date: Mon, 4 Jun 2012 17:08:14 +0100
Subject: Re: [EnergyPlus_Support] infiltration

Thank you for the answer on that.

As far as the infiltration is concerned,

I am given a value of 133 m3/h and I guess that this value concerns the whole building.

How can I use this value for each thermal zone? Do I have to find out the volume of

each thermal zone and solve the n=q/v (ach) equation for each thermal zone?

thank you,

theo

From: Thodwris Xaritidis <maki_to_fai@xxxxxxxxx>
To: "EnergyPlus_Support@xxxxxxxxxxxxxxx" <EnergyPlus_Support@xxxxxxxxxxxxxxx>
Sent: Sunday, 3 June 2012, 14:15
Subject: Re: [EnergyPlus_Support] infiltration-nat. ventilation

Hello again,

In the building that I am simulating I ve been given a value

for infiltration and one for nat vent for the whole building.

Is there any option to e+ to apply the total infiltration/ vent. portion automatically in the whole construction?

Or else how can I be sure which are the correct values for each zone?

thank you

From: FrancescoP <direzionecontraria@xxxxxxxx>
To: EnergyPlus_Support@xxxxxxxxxxxxxxx
Sent: Sunday, 3 June 2012, 10:43
Subject: [EnergyPlus_Support] Re: GetSpecificHeatGlycol: Temperature is out of range

I have the same problem:

sometimes the temperature is too low

************* ** Warning ** GetSpecificHeatGlycol: Temperature out of range (too low) for fluid specific heat
************* ** ~~~ ** This error occurred 58225 total times;
************* ** ~~~ ** during Warmup 0 times;
************* ** ~~~ ** during Sizing 0 times.
************* ** ~~~ ** Max=-9.894200E-003 {C} Min=-11.665963 {C}

and sometimes (actually, a lot of times...) it is too high

************* ** Warning ** GetSpecificHeatGlycol: Temperature out of range (too high) for fluid specific heat
************* ** ~~~ ** This error occurred 3949461 total times;
************* ** ~~~ ** during Warmup 0 times;
************* ** ~~~ ** during Sizing 0 times.
************* ** ~~~ ** Max=277.409112 {C} Min=125.000118 {C}

Any suggestion?
Best Regards

--- In EnergyPlus_Support@xxxxxxxxxxxxxxx, Omar Tabuyo <omartabuyo@...> wrote:
>
> Dear all,
>
> Anyone knows how i could solve this warnning? I have checked all system nodes temperature and there is not any node which temperature is upper 85ºC
>
> ** Warning ** GetSpecificHeatGlycol: Temperature is out of range (too high) for fluid specific heat **
> ** ~~~ ** ..Called From:UpdateSolarCollector Fluid name =WATER,Temperature=129.79
> ** ~~~ ** Environment=RUN PERIOD, at Simulation time=01/06 12:15 - 12:30
>
> Do this warnning modify the simulation results?
>
> What is the warnning meaning?
>
> Thanks
>

__._,_.___

Primary EnergyPlus support is found at: http://energyplus.helpserve.com or send a message to energyplus-support@xxxxxxxx The primary EnergyPlus web site is found at: http://www.energyplus.gov The group web site is: http://groups.yahoo.com/group/EnergyPlus_Support/ Attachments are currently allowed but be mindful that not everyone has a high speed connection. Limit attachments to small files. EnergyPlus Documentation is searchable. Open EPlusMainMenu.pdf under the Documentation link and press the "search" button.

Your email settings: Individual Email|Traditional
Change settings via the Web (Yahoo! ID required)
Change settings via email: Switch delivery to Daily Digest | Switch to Fully Featured
Visit Your Group | Yahoo! Groups Terms of Use | Unsubscribe

__,_._,___