Re: [EnergyPlus_Support] Processing IDF file error

[Edwin Lee <leeed2001@xxxxxxxxx>]

You may want to delete your .err file and retry running the simulation. Â It is possible that error file was carried over from a previous run. Â (Happened to me several times before!!)

Edwin

On Wed, Aug 12, 2009 at 09:56, YuanLu å??å?­ Li <yli006@xxxxxxxxxxx> wrote:

 

Hi, XingShi
 
Your message confirmed what I said in the other mail.
 
1.idf may be all right, if you do have that file, and the file and ExampleFiles directory are not read only protected..
 
I do not think there is 1.epw in your weatherData directory.
 
Therefore the simullation crashed.
 
If your IDF file and/or the weather file are not in the ExampleFiles  and weatherData Directory respectively, the batch file needs to be modified.

 Dr. Li  

 

---

To: EnergyPlus_Support@xxxxxxxxxxxxxxx; EnergyPlus_Support@xxxxxxxxxxxxxxx
From: xing.shi.2006@xxxxxxxxx

Date: Wed, 12 Aug 2009 22:35:34 +0800
Subject: Re: Re: Re: [EnergyPlus_Support] Processing IDF file error

 



I tried that and basically got the following:

 

Input File: ExampleFiles\1.idf

Output Files: ExampleFiles\Outputs\

Weather Files: WeatherData\1.epw

Beging EnergyPlus Processing...

....

....

Processing Data Dictionary

Processing Input File

Reporting Surfaces

**FATAL: Error condition occured. Previous Severe Errors cause termination.

 

What went wrong and how to fix it?  Thanks!

---

å??件人ï¼? Linda Lawrie

å??é??æ?¶é?´ï¼? 2009-08-12  21:46:12

�件人� EnergyPlus_Support

æ??é??ï¼?

主�� Re: Re: [EnergyPlus_Support] Processing IDF file error

 

suggest you take out any @echo off or comment it at the top of the runeplus batch file and see what is really executing.

At 07:39 AM 8/12/2009, xing.shi.2006 wrote:



 
 
 
If run in DOS mode, it did fail in the input processor and there was no audit file created.
 
I am puzzled by the fact that the same IDF file ran just fine in EP-Launch.  Is there anything with using "runeplus 1 1" in DOS mode that I am missing here?
 
XS
 
 

Ã¥ â??件人ï¼? Richard Raustad
Ã¥ â??éâ?¬ æ?¶é?´ï¼? 2009-009-08-12  21:03:53
æâ??¶ä»¶äººï¼? EnergyPlus_Support
æ?ââ??é? ï¼?
主�� Re: [EnergyPllus_Support] Processing IDF file error
 

It looks like it failed in the input processor (Fatal: " IP "). This
would be before the error file is created. See if there is an audit file
(eplusout.audit) that you can look at. I am not sure if you will find
the error at the end of this file, or somewhere in the middle.

xing.shi.2006 wrote:
>
>
> When using EP-Launch, there is no error in the ERR file. 0 Warning, 0
> Severe errors.
>
> When using DOS mode to run the same IDF file, it did not yield ERR
> file. I think the program just stopped somewhere before the ERR file
> was produced.
>
> It might be caused by the IDF file because I tried another IDF file
> and it ran just fine in both DOS mode and EP-Launch. The thing I
> don't understand is that the same IDF file runs ok in EP-Lauch but not
> in "runeplus 1 1" mode.
>
> XS
>
>

--
Richard A. Raustad
Senior Research Engineer
Florida Solar Energy Center
University of Central Florida
1679 Clearlake Road
Cocoa, FL 32922-5703
Phone: (321) 638-1454
Fax: (321) 638-1439 or 1010
Visit our web site at: http://www.fsec.ucf.edu

UCF - From Promise to Prominence: Celebrating 40 Years

---

Stay in the loop and chat with friends, right from your inbox! Learn how!

__._,_.___

The primary EnergyPlus web site is found at:
http://www.energyplus.gov

The group web site is:
http://groups.yahoo.com/group/EnergyPlus_Support/

Attachments are not allowed -- please post any files to the appropriate folder in the Files area of the Support Web Site.

EnergyPlus Documentation is searchable.  Open EPlusMainMenu.pdf under the Documentation link and press the "search" button.

Your email settings: Individual Email|Traditional
Change settings via the Web (Yahoo! ID required)
Change settings via email: Switch delivery to Daily Digest | Switch to Fully Featured
Visit Your Group | Yahoo! Groups Terms of Use | Unsubscribe

__,_._,___