[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [EnergyPlus_Support] Problems with extracting hourly variables from EnergyPlus





Mmm...there are usually report variables availible for surfaces. The keyword "surface" should be in there somewhere. The variables you mentioned seem mainly "zone average" types which apply to all the zone facing surfaces. The "surface" variables you need, you'll need to replace the wild card '*' with the specific surface name. You'll obviously be looking for radiation and convection rates from this specific surface.

I've only looked at temperature until now, but I'm sure Jerimia has controlled the heat flows more concisely.

Post the rdd...some of the variable names have changed in the v8 release, but we could try and filter out the right ones.

Mit freundlichen GrüÃ?en- Sent from my iPhone (excuse the brevity)

i. A.
Jean Marais
b.i.g. bechtold
Tel.   +49 30 6706662-23

On 30.09.2013, at 19:35, Joe Huang <YJHuang@xxxxxxxxxxxxxxxxxxxxxxxx> wrote:

 

Thanks to Jeremiah, Linda, and Jean for their replies and tips.

I wasn't aware of the Output:VariableDictionary,IDF; and *.rdd features in EnergyPlus, and am now able to get some of the hourly variables of interest.����

However, I still haven't an output variable giving the net heat flow from an interior surface into a zone.���� What I see in the *.rdd are just these five variables for interior surfaces:

Output:Variable,*,Surface Int Adjacent Air Temperature,hourly; !- Zone Average [C]
Output:Variable,*,Surface Int Convection Coeff,hourly; !- Zone Average [W/m2-K]
Output:Variable,*,Surface Int Convection Heat Rate,hourly; !- Zone Average [W]
Output:Variable,*,Surface Int Convection Heat Rate per Area,hourly; !- Zone Average [W/m2]
Output:Variable,*,Surface Int Convection Heat Gain to Air,hourly; !- Zone Sum [J]

I've extracted the 3rd and 5th ones, but found they were the same when converted to the same units.���� They also seem too small to be the total heat flow from the surface. Are there any other variables that track the radiative heat flow or the conductive heat flow from the surface?

Joe

Joe Huang
White Box Technologies, Inc.
346 Rheem Blvd., Suite 108D
Moraga CA 94556
yjhuang@xxxxxxxxxxxxxxxxxxxxxxxx
http://weather.whiteboxtechnologies.com for simulation-ready weather data
(o) (925)388-0265
(c) (510)928-2683
"building energy simulations at your fingertips"

On 28/09/2013 3:31 AM, jeannieboef@xxxxxxxxx wrote:
����
I'm with Jerimia on this one:
Specify the output variable dictionary to output an .rdd file in IDF format.
Run the simulation to produce the rdd file (which will list all the possible output variables for your simulation).����
Open the rdd in a text editor, and copy paste the output variables that you want to include in your simulation and re-run.

The trickiest part are the definitions of the different outputs. You'll have to search the documentation for the ones which look interesting.����

Mit freundlichen Gr��������en- Sent from my iPhone����(excuse the brevity)

i. A.
Jean Marais
b.i.g. bechtold
Tel. ���� +49 30 6706662-23

On 27.09.2013, at 23:09, Joe Huang <YJHuang@xxxxxxxxxxxxxxxxxxxxxxxx> wrote:

����

I'm doing some diagnostic simulations comparing EnergyPlus to another program (not DOE-2 :-)), and need to extract hourly variables for zone air temperature, inside surface temperature and heat fluxes through an interior wall.���� I took some old IDFs from 6 years ago, ran them through the IDFVersionUpdater to get Version 8.0 IDFs, and used the resultant reporting for the zone air temperature, but I'm not getting anything in the output *.eso.

���� Output:Variable,*,Site Outdoor Air Drybulb Temperature,Monthly;�������� < this works
���� Output:Variable,*,Zone/Sys Air Temp,Hourly;�������������������������������������������������������������������� < this does not work
���� Output:Variable,*,Zone Air System Sensible Cooling Rate,Monthly;������������ < this works
���� Output:Variable,*,Zone Air System Sensible Heating Rate,Monthly;�������� < this does not work

����Also, what is the syntax for specifying the heat flux for a particular surface ?���� I tried this but it doesn't work:

���� Output:Variable,
������������ *,���������������������������������������������������������������������������������������� !- Key_Value
������������ HOUSE:AT-FLOOR2 Heat Flow,���� !- Variable_Name
������������ Hourly;�������������������������������������������������������������������� !- Reporting_Frequency

Thanks

Joe Huang
White Box Technologies, Inc.
346 Rheem Blvd., Suite 108D
Moraga CA 94556
yjhuang@xxxxxxxxxxxxxxxxxxxxxxxx
http://weather.whiteboxtechnologies.com for simulation-ready weather data
(o) (925)388-0265
(c) (510)928-2683
"building energy simulations at your fingertips"



__._,_.___


Primary EnergyPlus support is found at:
http://energyplus.helpserve.com or send a message to energyplus-support@xxxxxxxx

The primary EnergyPlus web site is found at:
http://www.energyplus.gov

The group web site is:
http://groups.yahoo.com/group/EnergyPlus_Support/

Attachments are currently allowed but be mindful that not everyone has a high speed connection.  Limit attachments to small files.

EnergyPlus Documentation is searchable.  Open EPlusMainMenu.pdf under the Documentation link and press the "search" button.




Your email settings: Individual Email|Traditional
Change settings via the Web (Yahoo! ID required)
Change settings via email: Switch delivery to Daily Digest | Switch to Fully Featured
Visit Your Group | Yahoo! Groups Terms of Use | Unsubscribe

__,_._,___